Pitney Bowes DA80F - Page 196

I-4
Index
DA50S/DA55S/DA70S/DA75S AddressRight™ Printers Service Manual (SV61831 Rev. A)
Low Ink Warning in LCD Setup Menu A-18
Maintenance 7-2
Pre-Purge in LCD Setup Menu A-16
Purge Print Head, LCD Main Menu A-9
Printing Issues, Troubleshooting 4-19
Printing Standards
USPS® Delivery Point Barcode (DPBC) E-1
USPS® PLANET Code Barcode E-3
Print Modes (Print Resolution) 2-3
Print Quality, LCD Main Menu A-6
Print Samples for Troubleshooting 4-12
Print Specifi cations 2-3
Product Description 2-1
Publications/Information, Related 1-1
Purge Print Head, LCD Main Menu A-9
Purpose of this Manual 1-1
R
Rear Cover/Side Guides on Standard Feeder,
DA95F
Removal 5-39
Rear Cover and Main ProcessorBoard, DA95F
Removal 5-51
Removal and Replacement Procedures
DA80F (WF81)
Encoder Assembly 5-6
Entry Idler Roller Arm 5-28
Exit (Rubber) Roller 5-36
Feed Deck 5-30
Feeder Sensor Assembly (Emitter and Receiver)
5-10
Feed Motor Assembly and Feed Motor Encoder
Harness Assembly 5-16
Feed Motor Timing Belt 5-13
Feed Roller Pulley and FeedRoller Assembly 5-
14
Front Bottom Cover Assembly 5-11
Front Plate Assembly 5-32
H-Block Assembly (Media Separators) 5-20
Main Processor Board 5-4
Paper Bottom Sensor Assembly (Receiver) 5-9
Paper Top Sensor Assembly (Emitter) 5-9
Power Supply 5-37
Print Head Access Door 5-38
Print Head Cables and Boards 5-21
Rear Cover and Keyboard/LCD Display Board
5-3
Transport (Metal Grit) Roller 5-34
Transport Motor Assembly 5-18
Transport Timing Belt 5-12
DA95F (WF96)
Belt Drive Assembly 5-67
Drive Belt/Motor Assembly 5-74
Encoder Assembly 5-71
Entry Roller Support Assembly 5-55
Front Cover andKeyboard/LCD Display Board
5-49
Idler Roller Support (Module A) Assembly 5-57
Idler Roller Support (Module B) Assembly and
Exit Sensor 5-58
Intermediate Idler Rollers Assembly 5-56
Media Belts 5-69
Paper Sensor and Sensor Bar 5-54
Power Supply 5-75
Printer Top Cover 5-48
Print Head Cables and Print Head Boards 5-59
Rear Cover and Main ProcessorBoard 5-51
DA95F (WF96), Standard Feeder
Feed Belts and Rollers on Standard Feeder 5-44
H Block Roller (Media Separator) on Standard
Feeder 5-43
Lower Sensor(Receiver) Assembly on Standard
Feeder 5-41
Motor/DriveAssembly on Standard Feeder 5-46
Rear Cover/Side Guides on Standard Feeder
5-39
Top Sensor (Emitter)Assembly on Standard
Feeder 5-42
Tools Required 5-1
Rollers
Entry Idler Roller Arm Removal, DA80F 5-28
Entry Roller Support Assembly Removal, DA95F
5-55
Exit (Rubber) Roller Removal, DA80F 5-36
Feed Belts and Rollers Removal on Standard
Feeder, DA95F 5-44
Feeding problems when worn 4-15
Feed Roller Pulley and Feed Roller Assembly Re-
moval, DA80F 5-14
Idler Roller Support (Module A) Assembly Removal,
DA95F 5-57
Idler Roller Support (Module B) Assembly Removal,
DA95F 5-58
Intermediate Idler Rollers Assembly Removal,
DA95F 5-56
Maintenance 7-2
Theory 3-5
Transport (Metal Grit) Roller Removal, DA80F 5-34
ROM Revision Number, LCD Setup Menu A-21