To Next Page
S
sarahdanielsAug 25, 2025
What does 'No Cal' mean on Raven Farm Equipment and how do I fix it?
- DDavid SanchezAug 26, 2025
If your Raven Farm Equipment displays 'No Cal', calibrate the SmarTrax system using the calibration wizard.
What does 'No Cal' mean on Raven Farm Equipment and how do I fix it?
If your Raven Farm Equipment displays 'No Cal', calibrate the SmarTrax system using the calibration wizard.
Why does Raven SmarTrax machine consistently drive to the left or right of the guidance line?
If your Raven Farm Equipment machine consistently drives to the left or right of the guidance line, recalibrate the yaw sensor to zero while the machine is stationary and reset the SPS/WAS center calibration. Lower the appropriate PWM Min value until the front wheels steer very slowly manually and with minimum buttons. Increase the LA Aggressiveness and OL Sensitivity settings.
What does 'Road Mode' mean on Raven SmarTrax Farm Equipment and how do I fix it?
If your Raven Farm Equipment is displaying 'Road Mode', switch the roading switch to the on position.
Why can't I manually steer left or right from the System Diagnostics screen on Raven Farm Equipment?
If you cannot manually steer left or right from the System Diagnostics screen on your Raven Farm Equipment, check the hose connections and the node status lights for high current (HC) power. Also, check the power/ground fuses and connections and the solenoids on the SmarTrax valve for proper connection and voltage. Inspect the cable for shorts or breaks. Verify PWM Max settings are set correctly in the field computer and if you have SmarTrax hydraulic valve part numbers 334-0003-056 through 334-0003-079, verify FC adjustment is turned all the way out (typically eight or nine threads are visible beyond the jam nuts).
Why does Raven SmarTrax Farm Equipment valve makes noise all of the time?
If your Raven Farm Equipment valve makes noise all of the time, inspect the load sense orifice for blockage. If the problem persists, install the SmarTrax hydraulic valve recommended for the machine being used.
Why does Raven Farm Equipment valve makes noise in stand-by mode?
If your Raven Farm Equipment valve makes noise in stand-by mode, adjust the relief valve on the SmarTrax valve until the noise stops.
Why don't the wheels turn fast enough in LA mode on Raven SmarTrax?
If your Raven Farm Equipment wheels do not turn fast enough in LA mode, increase the LA Aggressiveness setting.
What does '3D Hot' mean on Raven SmarTrax Farm Equipment and how do I fix it?
If your Raven Farm Equipment displays '3D Hot', recalibrate terrain compensation.
What does '3D Cold' mean on Raven Farm Equipment and how do I fix it?
If your Raven Farm Equipment displays '3D Cold', recalibrate terrain compensation.
What does 'TC Error' mean on Raven Farm Equipment and how do I fix it?
If your Raven Farm Equipment displays 'TC Error', the SmarTrax node must be repaired or replaced. Contact your local Raven dealer.
Guidelines for working safely with the hydraulic system, including protective equipment and fluid handling.
Precautions for electrical connections, polarity, and voltage requirements for the SmarTrax system.
Best practices for installing and operating the SmarTrax system for the first time.
Details on positioning the GPS antenna for optimal system performance and accuracy.
Explains common status and mode information displayed on the CR7 during SmarTrax operation.
Steps for setting up machine profiles and configuring machine-specific settings in the CR7.
Overview of the SmarTrax calibration wizard and initial setup steps for the system.
Information on tuning system performance and adjusting parameters like Line Acquisition and Sensitivity.
Defines common status icons and buttons used on the Viper 4/4+ display for SmarTrax.
Steps to configure GPS settings and ensure proper communication for the SmarTrax system.
Process for selecting machine types and setting up profiles for SmarTrax operation on Viper 4/4+.
Detailed procedure for calibrating the SmarTrax system using the setup wizard.
Guidelines for fine-tuning SmarTrax performance, including LA and OL modes.
Requirements for Viper Pro software and SmarTrax node software versions for compatibility.
How to interpret system status messages displayed on the Viper Pro screen.
Setting up machine profiles and specific configurations for SmarTrax on Viper Pro.
Step-by-step guide to calibrating the SmarTrax system with the Viper Pro.
Tuning SmarTrax parameters like LA and OL sensitivity for optimal field operation.
Specifies required software versions for Envizio Pro/Cruizer II and SmarTrax node.
Interpreting SmarTrax system status icons on the Envizio Pro/Cruizer II display.
Steps to configure machine profiles and specific settings for SmarTrax with Envizio Pro/Cruizer II.
Guide for calibrating the SmarTrax system when used with Envizio Pro or Cruizer II.
Adjusting SmarTrax settings like LA and OL sensitivity for optimal field operation.
Explains SmarTrax CAN control node LEDs for diagnosing system issues.
Lists common SmarTrax error messages, their causes, and corrective actions.
Provides a wiring diagram for the SmarTrax 3D system with specific field computers.
General| Brand | Raven |
|---|---|
| Model | SmarTrax |
| Category | Farm Equipment |
| Language | English |
