Rohde & Schwarz NRP2 - Page 228

Remote Control - Commands
NRP2
225User Manual 1173.9140.02 ─ 07
CALCulate<[1]..8>:LIMit:CLEar:AUTO..............................................................................227
CALCulate<[1]..8>:LIMit:FAIL?
........................................................................................ 228
CALCulate<[1]..8>:LIMit:FCOunt?....................................................................................228
CALCulate<[1]..8>:LIMit:LOWer[:DATA]........................................................................... 228
CALCulate<[1]..8>:LIMit:LOWer[:DATA]:POWer................................................................229
CALCulate<[1]..8>:LIMit:LOWer[:DATA]:RATio................................................................. 229
CALCulate<[1]..8>:LIMit:LOWer:STATe............................................................................229
CALCulate<[1]..8>:LIMit:STATe.......................................................................................229
CALCulate<[1]..8>:LIMit:UPPer[:DATA]............................................................................230
CALCulate<[1]..8>:LIMit:UPPer[:DATA]:POWer................................................................ 230
CALCulate<[1]..8>:LIMit:UPPer[:DATA]:RATio.................................................................. 230
CALCulate<[1]..8>:LIMit:UPPer:STATe............................................................................ 230
CALCulate<[1]..8>:MATH[:EXPRession]...........................................................................231
CALCulate<[1]..8>:MATH[:EXPRession]:CATalog?........................................................... 232
CALCulate<[1]..8>:MAXimum:DATA?.............................................................................. 232
CALCulate<[1]..8>:MINimum:DATA?................................................................................232
CALCulate<[1]..8>:MEAN:DATA?.................................................................................... 232
CALCulate<[1]..8>:PTPeak:DATA?..................................................................................233
CALCulate<[1]..8>:RELative[:MAGNitude]........................................................................ 233
CALCulate<[1]..8>:RELative[:MAGNitude]:AUTO.............................................................. 233
CALCulate<[1]..8>:RELative:POWer[:MAGNitude].............................................................234
CALCulate<[1]..8>:RELative:RATio[:MAGNitude].............................................................. 234
CALCulate<[1]..8>:RELative:STATe.................................................................................234
CALCulate<[1]..8>:SDEViation:DATA?.............................................................................234
CALCulate<[1]..4>:STATistics:MARKer: HORIzontal:POSition[:X][:POWer] .........................235
CALCulate<[1]..4>:STATistics:MARKer:HORizontal:DATA?............................................... 235
CALCulate<[1]..4>:STATistics:MARKer:VERTical:POSition[:Y]........................................... 235
CALCulate<[1]..4>:STATistics:MARKer:VERTical:DATA[:POWer]?..................................... 235
CALCulate<[1]..4>:STATistics:POWer:AVG:DATA?...........................................................236
CALCulate<[1]..8>:TRACe:MARKer:XDELta?................................................................... 236
CALCulate<[1]..8>:TRACe:MARKer:YDELta?................................................................... 236
CALCulate<[1]..8>:TRACe:MARKer<[1]..2>:XPOSition...................................................... 236
CALCulate<[1]..8>:TRACe:MARKer<[1]..2>:YPOSition?.................................................... 237
CALCulate<[1]..8>:COUNt:DATA?
Queries the number of measured values that are included when the mean value and
standard deviation are calculated (in the above formulas referred to as N, see Mean
value of all measured values and Standard deviation σof all measured values).
Usage: Query only
CALCulate<[1]..8>:DATA?
With this command the current output value of a calculate block can be queried.
The unit is the current unit of the measured result.
Possible Units: W | DBM | DBUV | DPCT | DB | O
Usage: Query only
CALCulate (Configuration of Calculate Blocks)
北京海洋兴业科技股份有限公司（证券代码：839145）
电话：010-62176775
网址：www.hyxyyq.com