What to do if a warning or error appears during Roland Recording Equipment installation (Windows)?
If you encounter a warning or error during the installation of your Roland OCTA-CAPTURE on Windows, it may be because you connected the OCTA-CAPTURE to your computer before installing the driver or there are any devices labeled “Other,” “Unknown,” or “?/!/X” in the Device Manager. In both cases, reinstall the OCTA-CAPTURE driver.
How to increase the microphone volume on Roland Recording Equipment?
If you're experiencing insufficient microphone volume with your Roland OCTA-CAPTURE, ensure that: * The input impedance select switch is set to Lo-Z. * You connect your microphone to the XLR type connector of the combo input jack.
Why can't I play or record with my Roland Recording Equipment?
If you're unable to play or record with your Roland OCTA-CAPTURE, it could be due to these reasons: * The driver installation may have failed; reinstall the driver. * The sample rate setting of your software must match the sample rate setting of the OCTA-CAPTURE itself. * If the OCTA-CAPTURE’s sampling frequency is set to 192 kHz, the digital input/ output connectors, INPUT 5–8, and OUTPUT 5–8 cannot be used.
Why is the guitar volume insufficient with my Roland Recording Equipment?
If you're experiencing insufficient guitar volume with your Roland OCTA-CAPTURE, verify these settings: * Connect your guitar to the INPUT 2 combo input jack. * Set the input impedance select switch to the Hi-Z position. * Turn the OCTA-CAPTURE’s [SENS] knob toward the right to increase the input level. * Make connections using a cable that does not contain an internal resistor.
How to adjust the recording levels on Roland Recording Equipment?
If the recorded sound with your Roland OCTA-CAPTURE is too loud or too soft, use the OCTA-CAPTURE’s [SENS] knob to adjust the input level. Also, check your recording software's input level settings if it has that capability.
What to do if installation is not successfully completed when you connect Roland Recording Equipment?
If the installation of your Roland OCTA-CAPTURE is not successfully completed when you connect the device, consider the following: * After you connect the OCTA-CAPTURE, it may take several minutes before it is recognized by your computer. This is not a malfunction. Please wait until the Found New Hardware Wizard appears. * Make sure that the OCTA-CAPTURE is correctly connected to your computer. * Please use your computer with its power supply connected. * Disconnect all USB devices (other than a mouse and keyboard, if used) from your computer before performing the installation. * If your computer does not meet the requirements of the USB specification, you may be able to solve the problem by connecting a self-powered USB hub.
What to do if I can't install the Roland Recording Equipment driver?
If you're having trouble installing the Roland OCTA-CAPTURE driver, make sure of the following: * Log on to Windows with a user name belonging to the Administrators group, such as Administrator, or a user name whose account type is Computer Administrator. * If using Windows XP, refer to 'Driver Signing Option Settings (Windows XP)' and make the appropriate settings. * Close all other software before you perform the installation, as other software running in the background (such as anti-virus software) could interfere.
Why is there no sound from my computer speakers when using Roland Recording Equipment?
When the Roland OCTA-CAPTURE is connected to your computer, the sound will not be heard from your computer’s speakers. To hear sound, connect your headphones or audio playback system (external monitors) directly to the OCTA-CAPTURE.
Audio Channels| number of audio record channels (44.1/48/96 kHz) | 12 channels |
|---|---|
| number of audio playback channels (44.1/48/96 kHz) | 10 channels |
| number of audio record channels (192 kHz) | 4 channels |
| number of audio playback channels (192 kHz) | 4 channels |
Signal Processing| pc interface bit depth | 24-bit |
|---|---|
| ad/da conversion bit depth | 24-bit |
| internal processing bit depth | 40-bit |
Sampling Frequency| ad/da conversion sampling frequency | 44.1/48/96/192 kHz |
|---|---|
| digital (in/out) sampling frequency | 44.1/48/96 kHz |
Input and Output Levels| nominal input level (input jack 1-6, xlr type) | -56 to -6 dBu |
|---|---|
| nominal input level (input jack 7-8, xlr type) | -50 to +0 dBu |
| nominal input level (input jack 1-8, 1/4-inch trs phone type) | -46 to +4 dBu |
| nominal output level (output 1-8) | +0 dBu (balanced) |
| headroom | 16 dB |
Impedance| input impedance (input jack 1-6, xlr type) | 5 k ohms (balanced) |
|---|---|
| input impedance (input jack 7-8, xlr type) | 10 k ohms (balanced) |
| input impedance (input jack 1-8, 1/4-inch trs phone type) | 17 k ohms (balanced) |
| output impedance (output 1-8) | 1.8 k ohms (balanced) |
| output impedance (phones) | 47 ohms |
Frequency and Noise| frequency response (192 kHz) | 20 Hz to 90 kHz (+0/-8 dB) |
|---|---|
| frequency response (96 kHz) | 20 Hz to 40 kHz (+0/-2 dB) |
| frequency response (48 kHz) | 20 Hz to 22 kHz (+0/-2 dB) |
| frequency response (44.1 kHz) | 20 Hz to 20 kHz (+0/-2 dB) |
| residual noise level | -87 dBu typ. (GAIN: min., 600 ohms terminated, IHF-A) |
Dynamic Range and Display| dynamic range (ad block input 1-8) | 104 dB typ. (GAIN: min.) |
|---|---|
| dynamic range (da block output 1-8) | 113 dB typ. |
| display | 128 x 64 dots Graphic LCD (backlit LCD) |
Connectors| input jacks (xlr type / 1/4-inch trs phone type) | XLR type (balanced/phantom power +48 V), 1/4-inch TRS phone type (balanced) |
|---|---|
| coaxial input connector | present |
| coaxial output connector | present |
| headphone jack | Stereo 1/4-inch phone type |
| output jack (1/4-inch trs phone type) | balanced |
| midi connectors | In, Out |
| usb connector | present |
Power and Dimensions| power supply | DC 9 V (AC adaptor) |
|---|---|
| current draw | 1.45 A |
| dimensions | 283.8 (W) x 157.9 (D) x 50.4 (H) mm / 11-3/16 (W) x 6-1/4 (D) x 2 (H) inches |
| weight | 1.32 kg / 2 lbs 15 oz |
Lists critical safety instructions to prevent hazards like fire, shock, or injury.
Introduces the controls and indicators on the front of the OCTA-CAPTURE.
Introduces the connectors and ports on the rear of the OCTA-CAPTURE.
Provides a table outlining driver installation steps for different OS.
Step-by-step guide for installing the driver on Windows 7/Vista.
Details the User Account Control prompt and the driver setup wizard steps.
Explains selecting OCTA-CAPTURE as audio/MIDI device in software.
Step-by-step guide for installing the driver on Windows XP.
Explains the process for the Found New Hardware Wizard on Windows XP.
Selecting OCTA-CAPTURE as audio/MIDI device in software for XP.
Step-by-step guide for installing the driver on Mac OS X.
Selecting OCTA-CAPTURE as audio device in system settings for Mac.
Configuring MIDI settings in Audio MIDI Setup.
Setting up MIDI connections and testing transmission.
Illustrates connecting headphones or speakers for monitoring.
Instructions for playing sample audio files to verify setup.
Illustrates the physical connections for power, computer, and audio output.
Step-by-step guide for powering on the unit and connected equipment.
Step-by-step guide for powering off the unit and connected equipment.
How to select channels and adjust preamp gain using buttons and knob.
How to turn phantom power on/off for condenser microphones.
Guides on connecting and setting up microphones and guitars for recording.
How to set input impedance for Hi-Z or Lo-Z on channels 1 and 2.
Instructions for enabling or disabling phantom power.
How to adjust input sensitivity for optimal recording quality.
Explains how Auto Sens automatically sets recording levels.
How to adjust monitor sound balance without affecting recording level.
Guides on connecting multiple instruments for simultaneous recording.
Reiteration on adjusting input sensitivity for best quality.
Reiteration on adjusting monitor volume balance.
Overview of direct mixers and patch bay for monitoring and output assignment.
Explains the function of the dedicated control panel software.
Describes the main window, preamp, and direct mixer control screens.
Details settings like input gain, phantom power, phase, and low cut.
Explains compressor settings like Gate, Attack, Release, Ratio, Gain, Link.
Explains mixer select tabs and controls for input mixers.
Details controls like Stereo Link, Mute, Solo, Send, Pan, and Slider for input mixers.
Explains assigning output destinations for mixers and playback channels.
Guides on setting up monitor mixes for band members using direct mixers.
Instructions for linking two units for expanded I/O.
Configuring settings for two units on Windows, including driver settings.
Configuring settings for two units on Mac OS X, including MIDI and aggregate devices.
Configuring headphone monitoring when using two units.
Details how to adjust compressor parameters like THRS, GAIN, GATE, ATK, REL, RATIO, LINK.
Explains AUTO SENS, BACKUP/RECALL, VS EXPAND, DIGITAL, CLEAR MUTE/SOLO, POWER OFF, INITIALIZE.
How to match OCTA-CAPTURE's sampling frequency with software.
Steps to set the sampling frequency and restart the unit.
How to perform a factory reset using buttons and power.
How to adjust driver settings like audio buffer size in Windows.
Procedure to reinstall the driver if installation issues occur.
Checks for power-related problems like the unit not turning on.
Checks for common issues during driver installation.
Troubleshoots why sound is not heard from computer speakers.
Addresses issues with connected USB devices and VS EXPAND settings.
Troubleshoots coaxial synchronization and Mac OS X audio settings for two units.
Troubleshoots problems with hearing monitor sound from the second unit.
To Next Page
