Schweitzer Engineering SEL-387-0 - Page 425

A.3
Date Code 20170601 Instruction Manual SEL-387-0, -5, -6 Relay
Firmware and Manual Versions
Firmware
SEL-387-0-R608-V0-Z004003-D20050919
SEL-387-5-R608-V0-Z004003-D20050919
SEL-387-6-R608-V0-Z004003-D20050919
➤ Fixed ability to properly process SEL Fast Message data with cor-
rupted length field.
20050919
SEL-387-0-R607-V0-Z004003-D20050614
SEL-387-5-R607-V0-Z004003-D20050614
SEL-387-6-R607-V0-Z004003-D20050614
Supports PROTO=DNP
SEL-387-5-R409-V0-Z102102-D20050614
SEL-387-6-R406-V0-Z103103-D20050614
Does Not Support PROTO=DNP
SEL-387-6-R304-V0-Z003003-D20041018
➤ Manual update only (see Table A.2). 20050719
SEL-387-0-R607-V0-Z004003-D20050614
SEL-387-5-R607-V0-Z004003-D20050614
SEL-387-6-R607-V0-Z004003-D20050614
Supports PROTO=DNP
SEL-387-5-R409-V0-Z102102-D20050614
SEL-387-6-R406-V0-Z103103-D20050614
SEL-387-0
➤ Supports firmware modifications to SEL-387-5 and SEL-387-6.
SEL-387-5 and SEL-387-6
➤ Fixed DNP3 Index 216, 217, 218 Fault Time data types to provide
DNP3 Type 30, default variation 2 data (16 bit signed analog input).
20050614
Supports PROTO=DNP
SEL-387-6-R405-V0-Z103103-D20041018
Does Not Support PROTO=DNP
SEL-387-6-R304-V0-Z003003-D20041018
➤ Changed number of event summaries from 80 to 40. 20041018
SEL-387-5-R606-V0-Z004003-D20040628
SEL-387-6-R606-V0-Z004003-D20040628
SEL-387-0
➤ Supports firmware modifications to SEL-387-5 and SEL-387-6.
SEL-387-5 and SEL-387-6
➤ Added Direct SEL-2600A communications.
➤ Added Temperature Monitoring and Alarms.
➤ Added Dynamic Display capability.
➤ Added Through-Fault Monitor (SEL-387-5 only).
➤ Updated SEL-387-6 DSP. Note that this DSP change makes the
hardware functionally incompatible with all previous firmware
revisions (SEL-387-6 only).
20040628
Supports PROTO=DNP
SEL-387-6-R404-V0-Z103103-D20040312
Does Not Support PROTO=DNP
SEL-387-6-R303-V0-Z003003-D20040312
➤ Added through-fault event monitor, including the TFE serial port
commands.
20040312
SEL-387-0-R602-V0-Z003003-D20020118
SEL-387-5-R602-V0-Z003003-D20020118
Supports PROTO=DNP
SEL-387-6-R403-V0-Z102102-D20010518
Does Not Support PROTO=DNP
SEL-387-6-R302-V0-Z002002-D20010518
➤ Manual update only (see Table A.2). 20021004
SEL-387-0-R602-V0-Z003003-D20020118
SEL-387-5-R602-V0-Z003003-D20020118
Supports PROTO=DNP
SEL-387-6-R403-V0-Z102102-D20010518
Does Not Support PROTO=DNP
SEL-387-6-R302-V0-Z002002-D20010518
➤ Manual update only (see Table A.2). 20020118
Table A.1 Firmware Revision History—SEL-387-0, -5, -6 Relay (Sheet 2 of 5)
Firmware Identification (FID) Number Summary of Revisions
Manual
Date Code