Siemens Simantic ET200SP User Manual

Table of contents
Distributed I/O system
System Manual, 12/2016, A5E03576849-AG
9
5 Wiring ................................................................................................................................................... 75
5.1 Rules and regulations for operation ........................................................................................ 75
5.2 Additional rules and regulations for the operation of the ET 200SP with fail-safe
modules .................................................................................................................................. 77
5.2.1 Safety extra low voltage for fail-safe modules and fail-safe motor starters ............................ 77
5.2.2 Requirements for sensors and actuators for fail-safe modules and fail-safe motor
starters .................................................................................................................................... 78
5.2.3 Crosstalk of digital input/output signals .................................................................................. 81
5.3 Additional rules and instructions for operation with motor starters ......................................... 81
5.3.1 Protection against short circuit ................................................................................................ 81
5.4 Operating the ET 200SP on grounded incoming supply ........................................................ 82
5.5 Electrical configuration of the ET 200SP ................................................................................ 85
5.6 Wiring rules ............................................................................................................................. 87
5.7 Wiring BaseUnits for I/O modules ........................................................................................... 90
5.8 Connecting cable shields for I/O modules .............................................................................. 92
5.9 Wiring BaseUnits for motor starters ........................................................................................ 94
5.10 Connecting the 3DI/LC module for the motor starter .............................................................. 97
5.11 Connecting the supply voltage to the CPU/interface module ................................................. 99
5.12 Connecting interfaces for communication............................................................................. 101
5.12.1 Connecting PROFINET IO to the CPU/interface module via the bus adapter BA
2xRJ45 .................................................................................................................................. 101
5.12.2 Connecting PROFINET IO to the CPU/interface module via the BA 2xFC BusAdapter ...... 104
5.12.3 Connecting PROFINET IO to the CPU/interface module via BA 2xSCRJ BusAdapter ....... 108
5.12.4 Connecting PROFINET IO to the interface module via the BA SCRJ/RJ45 BusAdapter .... 111
5.12.5 Connecting PROFINET IO to the interface module via the BA SCRJ/FC BusAdapter ........ 113
5.12.6 Connecting PROFINET IO to the interface module via the BA 2xLC BusAdapter ............... 115
5.12.7 Connecting PROFINET IO to the interface module via the BA LC/RJ45 BusAdapter ......... 118
5.12.8 Connecting PROFINET IO to interface module via BA LC/FC BusAdapter ......................... 120
5.12.9 Connecting PROFINET IO (port P3) to the CPU .................................................................. 121
5.12.10 Connecting the PROFIBUS DP interface to the interface module/communications
module CM DP ...................................................................................................................... 123
5.13 Inserting I/O modules / motor starters and BU covers .......................................................... 124
5.14 Mounting/disassembly of motor starters ............................................................................... 126
5.14.1 Mounting the fan ................................................................................................................... 126
5.14.2 Mounting/disassembly of motor starters ............................................................................... 127
5.14.3 3DI/LC module ...................................................................................................................... 130
5.15 Labeling ET 200SP ............................................................................................................... 133
5.15.1 Factory markings .................................................................................................................. 133
5.15.2 Optional markings ................................................................................................................. 135
5.15.3 Applying color identification labels ........................................................................................ 137
5.15.4 Applying labeling strips ......................................................................................................... 138
5.15.5 Applying reference identification labels ................................................................................ 139

Siemens Simantic ET200SP Specifications

General

System Type	Modular I/O System
Mounting	DIN Rail
Power Supply	24 V DC
Category	I/O Systems
Protection Class	IP20
Modularity	Yes
Communication Protocols	PROFINET, PROFIBUS
Digital Inputs	Available (varies by module)
Digital Outputs	Available (varies by module)
Analog Inputs	Available (varies by module)
Analog Outputs	Available (varies by module)
Number of Modules per Station	Up to 64
Module Width	15 mm, 20 mm, 22.5 mm (depending on module type)