Siemens SIMATIC S5 ET 200U User Manual

1
2
3
4
5
6
7
8
B
9
A
 
ET 200U
Distributed I/O Station
Manual
Edition 03
System Overview
Technical
Description
Mechanical and Electrical
Configuration
ET 200U(DP Siemens):
Address Assignment, Starting
Up, Diagnosing Faults
EWA 4NEB 812 6087–02b
ET 200U(DP Standard):
Address Assignment, Starting
Up, Diagnosing Faults
Analog Value Processing
Module Spectrum
Function Modules
Safety–Related
Guidelines
Glossary
ET 200U(DP Standard/FMS):
Modes, Settings and Comm.
Cap. of the IM 318–C


Siemens SIMATIC S5 ET 200U Specifications

General

Modularity	Modular
Supply voltage	24 V DC
Protection Class	IP20
Type	I/O System
Category	I/O Systems
Digital inputs	Available (number varies by module)
Digital outputs	Available (number varies by module)
Analog inputs	Available (number varies by module)
Analog outputs	Available (number varies by module)
Relative Humidity	5% to 95% (non-condensing)
Dimensions	Varies depending on module configuration
Weight	Varies depending on module configuration

Summary

Technical Description

2.1 Design of the ET 200U Interface Module

Describes the physical components and indicators of the ET 200U interface module.

Mechanical and Electrical Configuration

3.1 Mechanical Configuration of the ET 200U Distributed I/O Station

Covers the physical installation, dismantling, and mounting of the ET 200U station.

3.2 Wiring the ET 200U Distributed I/O Station

3.3 Electrical Configuration of the ET 200U Distributed I/O Station

ET 200U(DP Siemens): Address Assignment, Starting Up, Diagnosing Faults Using COM ET 200

4.1 Assigning Addresses Using COM ET 200

Explains how to assign addresses to ET 200U(DP Siemens) modules using COM ET 200.

4.1.1 Using the CONFIGURING Screen for ET 200U(DP Siemens)

Details the steps for configuring the ET 200U(DP Siemens) using the CONFIGURING screen.

4.2 Starting Up and Testing with COM ET 200 for ET 200U(DP Siemens)

Guides users through the process of starting up and testing ET 200U(DP Siemens) stations with COM ET 200.

4.2.1 Setting the Station No. and Switch 8

Explains how to set the station number and switch 8 on the interface module.

4.2.2 Starting Up an ET 200U Slave Station

4.2.3 Using the SYSTEM START–UP/TEST Screen for an ET 200U(DP Siemens) Slave Station

4.3 Diagnosing Faults for ET 200U(DP Siemens)

Describes methods for diagnosing faults in ET 200U(DP Siemens) stations.

4.3.1 Using LEDs to Diagnose Problems

4.3.2 Using COM ET 200 to Diagnose Problems

4.3.3 Diagnosing Faults with STEP 5 (Station Diagnostics)

ET 200U(DP Standard): Address Assignment, Starting UP and Diagnosing Faults Using COM ET 200

5.1 Assigning Addresses Using COM ET 200

Explains address assignment for ET 200U(DP Standard) modules using COM ET 200.

5.1.1 Using the CONFIGURING Screen for ET 200U(DP Standard)

Details configuring ET 200U(DP Standard) modules via the CONFIGURING screen.

5.2 Starting Up and Testing with COM ET 200 for ET 200U(DP Standard)

Covers starting up and testing ET 200U(DP Standard) stations using COM ET 200.

5.2.1 Setting the Station No. and Switch 8

Explains setting the station number and switch 8 on the interface module.

5.2.2 Starting Up an ET 200U Slave Station

5.2.3 Using the SYSTEM START–UP/TEST Screen for an ET 200U(DP Standard) Slave Station

5.3 Diagnosing Faults for ET 200U(DP Standard)

Outlines fault diagnosis methods for ET 200U(DP Standard) systems.

5.3.1 Using LEDs to Diagnose Problems

5.3.2 Using COM ET 200 to Diagnose Problems

5.3.3 Diagnosing Faults with STEP 5 (Station Diagnostics)

ET 200U(DP Standard/FMS): Modes, Settings and Communications Capabilities of the IM 318–C

6.1 Modes of the IM 318–C

6.2 Settings of the IM 318–C

6.3 ET 200U(DP Standard/FMS) Communicating in Accordance with PROFIBUS Standard (Part 2)

Analog Value Processing

7.1 Analog Input Modules

7.2 Connecting Current and Voltage Sensors to Analog Input Modules

Provides instructions for connecting current and voltage sensors to analog input modules.

7.3 Start–Up of Analog Input Modules

7.5 Analog Output Modules

Function Modules

9.1 Comparator Module 2 x 0.5 to 20 mA / 0.5 to 10 V (6ES5 461–8MA11)

9.2 Timer Module 2 x 0.3 to 300 s (6ES5 380–8MA11)

9.3 Simulator Module (6ES5 788–8MA11)

9.4 Diagnostic Module (6ES5 330–8MA11)

9.5 Counter Module 2 x 0 to 500 Hz (6ES5 385–8MA11)

9.6 Counter Module 25/500 kHz (6ES5 385–8MB11)

9.7 Closed–Loop Control Module IP 262 (6ES5 262–8MA12)

Explains the function, modules, installation, addressing, and operating modes of the IP 262 module.

9.8 IP 263 Positioning Module (6ES5 263–8MA11)

Covers assignments of outputs, positioning, and technical specifications for the IP 263 module.

9.9 IP 264 Electronic Cam Controller Module (6ES5 264–8MA11)

Details the function, technical specifications, and Dead Time Compensation of the IP 264 module.

9.10 IP 265 High Speed Sub Control (6ES5 265–8MA01)

Describes the function, installation, and addressing of the IP 265 High Speed Sub Control module.

9.11 IP 266 Positioning Module (6ES5 266–8MA11)

Covers the operation principle, operating modes, installation, and restriction of the IP 266 positioning module.

9.12 IP 267 Stepper Motor Control Module (6ES5 267–8MA11)

Details the operation principle, LEDs, installation, and restriction of the IP 267 stepper motor control module.

9.13 CP 521 BASIC Communications Module (6ES5 521–8MB11)

Explains the function, installation, addressing, and technical specifications of the CP 521 BASIC module.

9.14 CP 521 SI Communications Processor (6ES5 521–8MA21)

Covers the function, unidirectional/bidirectional data exchange, and technical specifications of the CP 521 SI.

Safety–Related Guidelines

A.1 Active and Passive Faults in Automation Equipment

Procedures for Maintenance and Repair

A.2 Suggestions for Configuring and Installing a Programmable Controller