SMA HM-20 User Manual

Table of Contents
SMA Solar Technology AG
Operating manual 5HM-20-BE-en-19
11.4.2 Entering Line Conductors ................................................................................................................................ 62
11.4.3 Entering the PV Array Power .......................................................................................................................... 63
11.5 Adding a Switching Device............................................................................................................................. 63
11.5.1 Adding a Radio-Controlled Socket ................................................................................................................ 63
11.5.2 Adding Modbus Device.................................................................................................................................. 64
11.6 Adding direct communicating loads............................................................................................................... 65
11.6.1 Adding a Device with EEBus or SEMP Interface........................................................................................... 65
11.6.2 Pairing Loads via EEBus.................................................................................................................................. 65
11.7 Replacing the Sunny Home Manager............................................................................................................ 66
11.7.1 Resetting the Sunny Home Manager............................................................................................................. 67
11.7.2 Reassigning the Sunny Home Manager to the Sunny Portal System after the Reset.................................. 67
11.8 Restarting the Sunny Home Manager............................................................................................................ 68
11.9 Deleting devices from Sunny Portal................................................................................................................ 69
12 Load Control................................................................................................................................. 70
12.1 Background Information.................................................................................................................................. 70
12.1.1 Types of Loads................................................................................................................................................. 70
12.1.2 Communicating with Loads............................................................................................................................. 71
12.1.3 Controlling Loads via a Time Period .............................................................................................................. 71
12.1.3.1 Load MUST be switched on ........................................................................................................................... 72
12.1.3.2 Load CAN be switched on ............................................................................................................................. 72
12.1.4 Prioritizing Loads ............................................................................................................................................. 73
12.2 Load Overview and Planning ......................................................................................................................... 73
12.3 Configuring Switching Devices ....................................................................................................................... 75
12.3.1 Safety when Configuring Switching Devices................................................................................................. 75
12.3.2 Requirements for Configuring Switching Devices.......................................................................................... 76
12.3.3 Assigning a Load............................................................................................................................................. 76
12.3.4 Entering the Device Name.............................................................................................................................. 76
12.3.5 Configuring the Operating Mode.................................................................................................................. 76
12.3.6 Enabling Start-up Detection for Radio-Controlled Sockets ........................................................................... 77
12.4 Configuring Load Characteristics ................................................................................................................... 78
12.4.1 Entering general information .......................................................................................................................... 79
12.4.2 Selecting the Load Type.................................................................................................................................. 80
12.4.3 Selecting Program Controllability................................................................................................................... 80
12.4.4 Entering the Power Consumption ................................................................................................................... 81
12.4.5 Entering the Maximum Program Operating Time ......................................................................................... 81
12.4.6 Entering the Minimum Switch-On and Switch-Off Time ................................................................................ 82
12.4.7 Setting the Priority of the Load........................................................................................................................ 82
12.4.8 Assigning a Switching Device ........................................................................................................................ 83
12.4.9 Setting Measuring and Switching of the Assigned Device........................................................................... 83
12.4.10 Setting Automatic Switch-Off.......................................................................................................................... 83
12.5 Configuring the Time Period............................................................................................................................ 84
12.5.1 Setting or changing the time windows........................................................................................................... 85
12.5.2 Adding an additional time period.................................................................................................................. 86
12.5.3 Deleting a Time Period.................................................................................................................................... 86
12.6 Directly Controlling Loads............................................................................................................................... 87
13 Visualization of the energy management ................................................................................. 88
13.1 System selection with system list ..................................................................................................................... 88
13.2 System overview .............................................................................................................................................. 89
13.3 Current Status And Forecast ........................................................................................................................... 89
13.3.1 Overview Current Status Area ....................................................................................................................... 89
13.3.2 Overview Forecast and Recommended Action Area ................................................................................... 91
13.4 Energy Balance................................................................................................................................................ 92
13.5 Load Balance and Control.............................................................................................................................. 95

SMA HM-20 Specifications

General

Brand	SMA
Model	HM-20
Category	Measuring Instruments
Language	English