SSD 605C - Macro 99: 584 S Compatible Application

Application Macros 15-15
605C Frequency Inverter
DIGITAL INPUT 1
VALUE [ 31]
–
FALSE
FALSE – [ 30] INVERT
–
DIGITAL INPUT 3
VALUE [ 37]
–
FALSE
FALSE – [ 36] INVERT
–
DIGITAL INPUT 5
VALUE [ 43]
–
FALSE
FALSE – [ 42] INVERT
–
DIGITAL INPUT 2
VALUE [ 34]
–
FALSE
TRUE – [ 33] INVERT
–
DIGITAL INPUT 4
VALUE [ 40]
–
FALSE
TRUE – [ 39] INVERT
–
ANALOG INPUT 4
VALUE [722] – 0.00 %
BREAK [724] – FALSE
150.00 % – [720] SCALE –
0.00 % – [721] OFFSET –
0..+10 V – [719] TYPE –
FALSE – [718] BREAK ENABLE –
0.00 % – [723] BREAK VALUE –
SEQUENCING LOGIC
TRIPPED [289] – FALSE
RUNNING [285]
–
FALSE
JOGGING [302]
–
FALSE
STOPPING [303]
–
FALSE
OUTPUT CONTACTOR [286]
–
FALSE
SWITCH ON ENABLE [288]
–
FALSE
SWITCHED ON [306]
–
TRUE
READY [287]
–
FALSE
SYSTEM RESET [305]
–
TRUE
MAIN SEQ STATE [301]
–
NOT READY
REMOTE REV OUT [296]
–
FALSE
HEALTHY [274]
–
FALSE
FALSE
–
[291] RUN FWD
–
FALSE
–
[292] RUN REV
–
FALSE
–
[293] /STOP
–
FALSE
–
[280] JOG
–
TRUE
–
[276] DRIVE ENABLE
–
TRUE
–
[277] /FAST STOP
–
TRUE
–
[278] /COAST STOP
–
FALSE
–
[294] REMOTE REVERSE
–
FALSE
–
[282] REM TRIP RESET
–
TRUE
–
[290] TRIP RST BY RUN
–
FALSE
–
[283] POWER UP START
–
I/O TRIPS
FALSE – [234] EXTERNAL TRIP
–
FALSE
–
[235] INPUT 1 BREAK
–
FALSE
–
[236] INPUT 2 BREAK
–
VALUE FUNC 7
OUTPUT [163]
–
0.00 %
100.00 % – [160] INPUT A
–
0.00 %
–
[161] INPUT B
–
0.00 %
–
[162] INPUT C
–
SWITCH(A,B)
–
[164] TYPE
–
CURRENT LIMIT
LIMITING [370]
–
FALSE
100.00
%
– [365] MOTOR I LIMIT
–
-100.00
%
–
[623] REGEN I LIMIT
–
CURRENT
–
[366] FEEDBACK SOURCE
–
TRUE
–
[686] REGEN LIM ENABLE
–
ZERO SPEED
AT ZERO SPEED [360] – FALSE
0.00 % – [358] INPUT
–
0.50 %
–
[357] LEVEL
–
0.00 %
–
[359] BAND
–
VALUE FUNC 8
OUTPUT [168]
–
0.00 %
0.00 % – [165] INPUT A
–
0.00 %
–
[166] INPUT B
–
1.00 %
–
[167] INPUT C
–
WINDOW
–
[169] TYPE
–
LOGIC FUNC 1
OUTPUT [183]
–
FALSE
FALSE – [180] INPUT A
–
TRUE
–
[181] INPUT B
–
TRUE
–
[182] INPUT C
–
AND(A,B,!C)
–
[184] TYPE
–
CURRENT FEEDBACK
MOTOR CURRENT [ 66]
–
0.00 %
MOTOR CURRENT [ 67]
–
0.0 A
I MAGNETISING [ 68]
–
0.00 %
I MAGNETISING [ 69] – 0.0 A
I TORQUE [ 70]
–
0.00 %
I TORQUE [ 71]
–
0.0 A
LOAD [ 72]
–
0.00 %
FIELD [ 73]
–
0.00 %
**6.2 A – [ 64] FULL LOAD CALIB
–
**3.6 A
–
[ 65] NO LOAD CALIB
–
0.80
–
[242] POWER FACTOR
–
DIGITAL OUTPUT 1
FALSE – [ 52] VALUE
–
TRUE
–
[ 51] INVERT
–
DIGITAL OUTPUT 2
FALSE – [ 55] VALUE
–
FALSE
–
[ 54] INVERT
–
DIGITAL OUTPUT 3
FALSE – [737] VALUE
–
FALSE
–
[736] INVERT
–
ANALOG OUTPUT 1
0.00 % – [ 45] VALUE –
100.00 %
–
[ 46] SCALE
–
0.00 %
–
[ 47] OFFSET
–
TRUE
–
[ 48] ABS
–
0..+10 V
–
[ 49] TYPE
–
ANALOG OUTPUT 2
0.00 % – [731] VALUE –
66.67 %
–
[732] SCALE
–
0.00 %
–
[733] OFFSET
–
FALSE
–
[734] ABS
–
-10..+10 V
–
[735] TYPE
–
ITEM 4
ITEM 5
ITEM 6
ITEM 2
ITEM 7
feedback link
(7)
(37)
(40)
(24)
(39)
(38)
(41)
(42)
(31)
(28)
(34)
(33)
(1)
(2)
(3)
(4)
(5)
(26)
(27)
(6)
Macro 99: 584S Compatible Application