Unipulse F372A - Calibration (CAL0 to CAL3); System Setting

94
8 SUPPLEMENTS
94
SUPPLEMENTS
Chapter
8
■Calibration (CAL0 to CAL3)
Protect ○:Work Setting Protect, ◎:System Setting Protect, ●:Calibration Protect, レ:Expansion Protect
Memory S:SRAM, N:NOVRAM
*1 Calibration is bipolar. *2 See page91 "Unit Setting List".
■System setting
Operation Setting
RS-232C Setting
Page No. Item Initial value Setting range Memory Protect
1
1 Excitation Voltage 0: 2.5V
0: 2.5V 1: 10V
N
●
2 Zero Calibration 0
－ 3.000mV / V to 3.000mV / V
N
●
3
Equivalent Input
Calibration
3.000mV/V
－ 3.000mV / V to 3.000mV / V (0 is excluded.)
N
●
4 Actual Load Calibration 10000
－ 99999 to 99999
*1
(0 is excluded.)
N
●
5 Calibration Selecttion 0: Cal 0 0: Cal 0 1: Cal 1 2: Cal 2 3: Cal 3 4: EXT 0 N
●
2
6Unit kN *2 N
●
7 Increment 0: 1
0: 1 1: 2 2: 5 3: 10 4: 20 5: 50 6: 100
N
●
8 Digital Offset 0
－ 99999 to 99999
N
●
9
Digital Zero Limit 99999 0 to 99999 N
●
10 Calibration Selecttion 0: Cal 0 0: Cal 0 1: Cal 1 2: Cal 2 3: Cal 3 4: EXT 0 N
●
3
11
12
13
14
15
Page No. Item Initial value Setting range Memory Protect
1
1 Digital Filter OFF
0: OFF，2 to 999 Times
N
◎
2 Analog Filter 2: 300Hz
0: 30 1: 100 2: 300 3: 1000 [Hz]
N
◎
3 Backlight
ON time：
10 Min
0 to 99 Min (Always ON time when "0".)
N
◎
Bright →Dark：
0 Min
0 to 99 Min (Always Bright when "0")
*
4 Language
0: JPN( 日） 0: JPN( 日） 1:ENG( 英 )
N
◎
5 SI/F Print Out OFF
0: OFF 1: MD 2: HOLD
N
◎
2
6 Motion Detect
0.0 sec /
0count
0.0 to 9.9 sec / 0 to 99 count N
◎
7 Zero Tracking
0.0 sec /
0count
0.0 to 9.9 sec / 0 to 99 count N
◎
8
Vol. Out Filter 1: ON
0: OFF 1: ON
N
◎
9
Indicate Color Yellow 0: Yellow 1: Green 2: Blue 3: Comparison N
◎
10
B5 Func. Select 0: WORK 3
0: WORK 3 1: DSP_LOCK 2: KEY_LOCK
N
◎
3
11
B6 OFF Det. Wait 0.00 sec 0.00 to 1.00 sec N
◎
12
B8 OFF Det. Wait 0.00 sec 0.00 to 1.00 sec N
◎
13
Measurement work
selection
1: EXT.
0: COM. 1: EXT.
N
◎
14
Control input selection 1: EXT.
0: COM. 1: EXT.
N
◎
15 Password
1
1 Communication Mode 0: Normal
0: Normal 1: Continue 2: Print
N
◎
2 Baudrate 1: 19200bps
0: 9600 1: 19200 2: 38400 3: 57600 [bps]
N
◎
3 Data Bit 1: 8bit
0: 7bit 1: 8bit
N
◎
4Stop Bit 0: 1bit
0: 1bit 1: 2bit
N
◎
5 Parity Bit 1: EVEN
0: NONE 1: EVEN 2: ODD
N
◎
2
6 Delimiter 0: CR
0: CR 1: CR+LF
N
◎
7
Flow Control 0: OFF
0: OFF 1: RTS/CTS
N
◎
8
9
10