4RF Aprisa XE - Page 182

To Next Page

To Previous Page

Maintenance | 181

To clear your web browser cache (Internet Explorer 6.x and above):

1. Select Tools > Internet Options.

2. On the General tab, click Delete Files, and then click OK to confirm.

Main Page

Default Chapter6
- Table of Contents6
1 Getting Started12
2 Introduction16
- About this Manual16
- What's in the Box16
  - Aprisa CD Contents17
  - Accessory Kit18
3 Preparation20
- Path Planning20
- Site Requirements24
4 About the Terminal26
- Introduction26
- Modules27
- Front Panel Connections and Indicators28
- Interface Card Types29
5 Mounting and Installing the Terminal30
- Required Tools30
- Installing the Terminal30
- Installing the Antenna and Feeder Cable31
- External Alarms32
  - Alarm Circuit Setup32
- Interface Cabling33
- Power Supplies33
- Bench Setup38
6 Connecting to the Terminal40
- Connecting to the Terminal's Setup Port40
- Connecting to the Terminal's Ethernet Interface43
  - PC Requirements for Supervisor44
  - PC Settings for Supervisor45
- IP Addressing of Terminals48
- Network IP Addressing49
  - Same Subnet as Local PC49
  - Different Subnet as Local PC50
7 Managing the Terminal52
- The Setup Menu52
- 4RF Supervisor54
  - Logging in55
  - Logging out55
- Supervisor Opening Page56
- Changing the Terminal's IP Address57
- Setting up Users58
8 Configuring the Terminal62
- Configuring the RF Settings62
  - Transmit Power63
  - Modem Performance Settings64
- Entering Terminal Information65
- Configuring the IP Settings66
- Saving the Terminal's Configuration67
- SNMP (Simple Network Management Protocol)68
- Setting the Terminal Clock Sources72
- Configuring the RSSI Alarm Threshold74
- Configuring the External Alarms75
  - Configuring the External Alarm Inputs75
  - Configuring the External Alarm Outputs77
9 Configuring the Traffic Interfaces78
- Viewing a Summary of the Interfaces78
- Configuring the Traffic Interfaces80
- Ethernet81
- QJET Port Settings88
- Q4EM Port Settings90
- DFXO / DFXS Loop Interface Circuits92
  - DFXS Port Settings95
  - DFXO Port Settings102
- QV24 Port Settings109
- HSS Port Settings110
- HSS Handshaking and Clocking112
  - HSS Handshaking and Control Line Function112
  - HSS Synchronous Clock Selection Modes115
10 Cross Connections122
- Embedded Cross Connect Switch122
  - Link Capacity Utilization122
- The Cross Connections Application122
- Configuring the Traffic Cross Connections134
- Cross Connection Example148
- Symmetrical Connection Wizard149
11 Protected Terminals154
- Monitored Hot Stand by (MHSB)154
12 In-Service Commissioning164
- Before You Start164
  - What You will Need164
- Applying Power to the Terminals165
- Review the Link Configurations Using Supervisor165
- Antenna Alignment166
13 Maintenance176
- Routine Maintenance176
- Terminal Upgrades177
- Rebooting the Terminal190
- Support Summary191
- Installing Interface Cards192
14 Troubleshooting198
- Loopbacks198
- Alarms200
- System Log208
  - Checking the Syslog208
  - Setting up for Remote Logging210
15 Interface Connections212
- RJ-45 Connector Pin Assignments212
- Interface Traffic Direction212
- QJET Interface Connections213
- Ethernet Interface Connections214
- Q4EM Interface Connections215
  - E&M Signalling Types216
- DFXS Interface Connections218
- DFXO Interface Connections219
- HSS Interface Connections220
  - Synchronous Cable Assemblies221
  - Cable WAN Connectors228
- QV24 Interface Connections229
16 Alarm Types and Sources230
- Alarm Types230
17 Country Specific Settings236
18 Specifications238
- RF Specifications238
- System Performance Specifications239
- Interface Specifications245
- Power Specifications253
- MHSB Specifications254
  - MHSB Protection254
- General Specifications254
19 Product End of Life256
- End-Of-Life Recycling Programme (WEEE)256
20 Abbreviations258
21 Acknowledgments and Licensing260
22 Commissioning Forms266
23 Index268

4RF Aprisa XE - Page 182

Table of Contents

Other manuals for 4RF Aprisa XE

Related product manuals