ABB SACE Emax 2 Series - Access from the Display

ABB | SACE Emax 2
Electronic accessories | 5 - Ekip Signalling 2K modules
187 | © 2013 ABB | 1SDH001000R0002 - L7804
Connections
The modules must be mounted on the terminal box of the circuit-breaker or of the fixed part of
the withdrawable circuit-breaker, in the first free slot after the Ekip Supply module.
Information on the assembly is available from the web site http://www.abb.com/abblibrary/
DownloadCenter/, in particular with the kit sheet 1SDH001000R0524.
The wiring diagrams for the modules are included below:
YO
01
H4
02
K5
04
K10K9
94
92
H3
9181
H2
82
K4
K8
8474
K7
K3
H1
72
7161
HC
62
64
54
52
51
EKIP SupplyModuleTrip Unit I/O
HC
K6
Ge-
Ge
Szc
K2
K1
W4
W3
R2
R1
Q4Q3Q2Q1YC2YC
YU
YO2
RTC
I/O
TU
44
42
41
34
32
31
24
22
21
14
12
11
C22
C21
C12
C13
C11
C2
C3
C1
D2
D1
48
46
45
Ne
Rca
Ne-
Gzi
Szo
Szi
Gzo
Rct
Vn
V1
V2
V3
U2
U1
38
36
35
98
96
95
YRMS33S51
EKIP Signalling 4KQ5..Q10
Module Module
HC
42
XV
A4
X
X
XV
A3
A4
H11
H11 H12
H12
H11
H12
K13
K14
K13
K14
K13
K14
I 12
O 12O 11
I 11
K12
K11
K12
K11
K12
K11
41
Ekip Signalling 2K-1
SIGN
K51
HC1
HC1
HC1
K51
SIGN
HC2
HC2
HC2
Ekip Signalling 2K-2
K21
K22
K21
K22
K21
K22
I 21
O 21 O 22
I 22
K24
K23
K24
K23
K24
K23
H22
H21
H22
H22H21
H21
* L), * M) * L), * M)
43
K51
SIGN
HC3
HC3
HC3
Ekip Signalling 2K-3
K31
K32
K31
K32
K31
K32
I 31
O 31 O 32
I 32
K34
K33
K34
K33
K34
K33
H32
H31
H32
H32H31
H31
* L), *M)
Diagrams 41 - 42 - 43
Further information is available on page 156, or on the site http://www.abb.com/abblibrary/
DownloadCenter/, where the wiring diagram is available 1SDM000091R0001.
Access from the display
With the modules energized, and the Local Bus enabled, the presence of the modules on the
terminal box activates additional menus on the display:
• In order to configure the inputs and output contacts.
• To display information on the modules and the state of inputs and outputs.
To enable the Local Bus, you need to select "On" in the menu Settings, Modules, Local Bus.
The following table illustrates the path for accessing the configuration parameters of the
modules from the display:
Settings
…
Network
frequency
Modules
Local/Remote
Local Bus
…
Ekip Signalling
2K-1
I 01
Signal source
Delay
I 02
(1)
O 01
Signal source
Delay
Contact Type
Self-latching
min Activation
Time
O 02
(2)
Ekip Signalling
2K-2
(3)
Ekip Signalling
2K-3
(3)
…
Function
Power
Controller
…
(1)
Like menu I 01.
(2)
Like menu O 01.
(3)
Like menu Signalling 2K-1.
NOTE: the modules can also be configured with the Ekip Connect application (see
the chapter “13 - Other accessories", and the paragraph "Ekip Connect application"
on page 221).
Continued on the next page