ABB tacteo KNX - Page 5

Table of contents
Product manual 2CKA001473B9482
│
5
11.5.43 Cooling control — Control value type ............................................................................................... 92
11.5.44 Cooling control — Cooling type ........................................................................................................ 93
11.5.45 Cooling control — P-component (x 0.1°C) ....................................................................................... 93
11.5.46 Cooling control — I-component (min.).............................................................................................. 94
11.5.47 Cooling control — Extended settings ............................................................................................... 94
11.5.48 Basic stage cooling............................................................................................................................ 95
11.5.49 Basic stage cooling — Status object cooling ................................................................................... 95
11.5.50 Basic stage cooling — Mode of the control value ............................................................................ 95
11.5.51 Basic stage heating - Control value difference for sending of heating control value ..................... 95
11.5.52 Basic stage cooling — Hysteresis (x 0.1°C) .................................................................................... 96
11.5.53 Basic stage cooling — Cyclic sending of the control value (min) ................................................... 96
11.5.54 Basic stage cooling - PWM cycle cooling (min) ............................................................................... 97
11.5.55 Basic stage cooling — Maximum control value (0 - 255) ................................................................ 97
11.5.56 Basic stage cooling — Minimum control value for basic load (0 to 255) ........................................ 97
11.5.57 Control of additional cooling stage ................................................................................................... 98
11.5.58 Control of additional cooling stage — Cooling type ......................................................................... 99
11.5.59 Control of additional cooling stage — P-component (x 0.1°C) ....................................................... 99
11.5.60 Control of additional cooling stage — P-component (min) ............................................................ 100
11.5.61 Control of additional cooling stage - Temperature difference to basic stage (x 0.1°C) ............... 100
11.5.62 Control of additional cooling stage — Extended settings .............................................................. 100
11.5.63 Additional cooling stage .................................................................................................................. 101
11.5.64 Additional cooling stage — Mode of the control value .................................................................. 101
11.5.65 Additional cooling stage — Hysteresis (x 0.1°C) ........................................................................... 101
11.5.66 Additional cooling stage — Control value difference for sending of cooling control value .......... 101
11.5.67 Additional cooling stage — Cyclic sending of the control value (min) .......................................... 102
11.5.68 Additional cooling stage — Maximum control value (0 - 255) ....................................................... 102
11.5.69 Additional cooling stage — Minimum control value for basic load (0 - 255) ................................ 102
11.5.70 Settings of basic load ...................................................................................................................... 103
11.5.71 Settings of basic load — Minimum control value for basic load > 0 ............................................. 103
11.5.72 Basic load settings — Basic load active when controller is off ..................................................... 103
11.5.73 Combined heating and cooling modes ........................................................................................... 1 0 4
11.5.74 Combined heating and cooling modes — Switchover of heating/cooling .................................... 104
11.5.75 Combined heating and cooling modes — Operating mode after reset ........................................ 104
11.5.76 Combined heating and cooling modes — Heating/cooling control value output ......................... 105
11.5.77 Combined heating and cooling modes — Additional heating/cooling stage control value
output ............................................................................................................................................... 105
11.5.78 Setpoint settings .............................................................................................................................. 106
11.5.79 Setpoint settings — Setpoint for heating comfort = setpoint for cooling comfort ......................... 106
11.5.80 Setpoint settings — Hysteresis for switchover heating/cooling (x 0.1°C)..................................... 106
11.5.81 Setpoint settings — Setpoint temperature for heating and cooling comfort (°C) ......................... 107
11.5.82 Setpoint settings — Setpoint temperature for heating comfort (°C) ............................................. 107
11.5.83 Setpoint settings — Reduction for standby heating (°C) ............................................................... 1 0 7
11.5.84 Setpoint settings — Reduction for ECO heating (°C) .................................................................... 107
11.5.85 Setpoint settings — Set-point temperature for frost protection (°C) ............................................. 108
11.5.86 Setpoint settings — Setpoint temperature for cooling comfort (°C) .............................................. 108
11.5.87 Setpoint settings — Increase for standby cooling (°C) .................................................................. 108
11.5.88 Setpoint settings — Increase for ECO cooling (°C) ....................................................................... 108
11.5.89 Setpoint settings — Set-point temperature for heat protection (°C) ............................................. 109
11.5.90 Setpoint settings — Display indicates ............................................................................................ 109
11.5.91 Setpoint settings — Send current setpoint ..................................................................................... 109
11.5.92 Setpoint settings — Cyclic sending of the current set-point temperature (min) ........................... 109
11.5.93 Setpoint settings - Basic set value is .............................................................................................. 110