Adtech ADTECH4 CNC Series - 3.3.3 Parameters Submenu

201 pages

To Next Page

To Previous Page

ADTECH4 SeriesCNC Maintenance Manual

3.3.3. Parameters submenu

3.3.4. Working coordinate submenu

[Edit] [Program]

[File]

[Parameters] [Comprehensive]

[Axis

configuration]

[Management]

[Tool changer]

[Principal axis]

[Port]

Main Page

Default Chapter5
- Table of Contents5
1 Foreword10
2 System Technical Features11
- Technical Parameters11
- System Functions13
- System Operating Condition14
3 Operating Panel15
- ADTCNC46 Series System LCD/ Button Panel15
LCD Display Unit16
- ADTCNC49 Series System LCD/ Button Panel17
- System Menus17
- Operating Keys22
4 Manual Operation23
- Returning to Reference Point Manually23
- Continuous Feeding Manually24
- Single Step Feeding25
- Hand Wheel Feeding26
- Manual Auxiliary Function Operation27
- Tool Setting29
  - Centered (M Series)29
Single Axis Centered29
Square Centered30
Plane Circle (XY Plane) Centered30
- Tool Regulator (M Series)32
- Tool Setting by Test Cutting (L Series)33
- Data Settings34
  - Tool Compensation Data Setting34
  - System Parameter Setting35
- System Shortcuts36
5 Automatic Operation37
- Memory Operation37
- MDI Operation37
- USB Disk DNC38
- Speed Rate Adjustment38
- Run Idle38
- SBK Function39
- BDT Function39
- Stopping Automatic Operating39
6 Safe Operation41
- Emergency Stop41
- Hard Limit over Travel41
- Soft Limit over Travel41
7 Alarm and Self-Diagnosis Function42
- NC Program Execution Alarm42
- System Environment Alarms44
- Alarm Processing46
- Self-Diagnosis46
8 Program Saving & Editing47
- Saving the Program in the Memory47
- Reading Programs into Work Area47
  - Reading Programs from Controller into Work Area47
  - Reading Programs from USB Disk into Work Area48
- Editing & Modifying Programs48
- Deleting Files48
  - Deleting Files in Memory48
9 Main Interfaces of the System50
- Position Interface50
- Programming Interface53
- MDI Interface55
MDI Interaction Interface Is Shown below55
1501 MDI Interface56
- File Management56
- Graphic Simulation57
- Parameter Interface58
IO Configuration Parameters61
IO Configuration Parameters Interface62
- Compensation Interface62
- M Series Workpiece Coordinate System Setting Interface63
- Controller Diagnosis Interface (Diagnosis)67
- Macro Variable View Interface (Macro Variable)68
- Current Mode Instruction Info69
10 System Maintenance70
- Restart70
- System Upgrade70
- Reset70
- Parameter Backup & Restore70
- Entering BISO Interface71
11 System Parameters72
- Parameter Index List73
- General Parameter (P1.)104
- Axis Parameter Configuration (P2.)119
- Management Parameter (P3.)139
- Tool Magazine Parameters (P4.)146
- Principal Axis Parameter (P5.)146
- Port Configuration (P6.)153
12 Hardware Interface Definition and Connection Instructions155
- Installation Layout155
- Interface Definition161
  - Motor Drive Control Interface161
  - Digital Input Interface164
Default Input Port Configuration of 46M Series (Milling Machine)166
Default Input Port Configuration of 46L Series XS5 (Lathe)167
Default Input Port Configuration of 49M Series XS7 (Milling Machine)168
- Digital Output Interface172
Default Output Port Configuration of M Series Milling Machine CNC4640(XS6), CNC4960(XS8)174
Default Output Port Configuration of M Series Milling Machine CNC4960(XS15)175
Default Output Port Configuration of L Series (Lathe)177
- Handheld Box Interface177
- Analog Output Interface (46 Series XS8)181
- Principal Axis Encoder Interface (46 Series XS12, 49 Series XS10)182
- RS232 Transmission Interface (46 Series XS9, 49 Series XS11)187
- USB Memory Connection Interface (46 Series XS10)187
- PC USB Communication Interface (46 Series XS11, 49 Series X13)187
- Electrical Connection Diagram187
ET102A Splitter Function Definition198
- ET202A Splitter Wiring Diagram200
- ET202A Splitter Function Definition200

Adtech ADTECH4 CNC Series - 3.3.3 Parameters Submenu

Table of Contents

Related product manuals