Home
Agilent Technologies
Test Equipment
3070
Agilent Technologies 3070 User Manual
4
of 1
of 1 rating
116 pages
Give review
Manual
Specs
To Previous Page
To Previous Page
Loading...
Printed in Singa
pore
06/2003
E9970-9000
1 Rev
.
H
115
Table of Contents
Table of Contents
2
E9970-90001 Rev. H
7
In this Chapter
7
Referenced Manuals
7
Tools Required
8
Getting Started
9
Verify Site Preparation Complete
9
Check for Shipping Damage
9
Check the Shipment against the Order before Uncrating
9
Un-Crate the System
9
Check the System and the Contents of All Crates and Boxes against the Order
9
Setting up the KVM and Support Arms
11
Install the KVM and Support Arms
11
Adjust the Support Arm Tension
21
Setting up the Strip Printer
23
Install the Strip Printer Tray
23
Preparing the Testhead
24
Install the Footswitch
24
Install the Probe and Probe Cradle
25
Install the Fixture Pull-Down Label -- Non-English Only
25
Attach the Site LAN Cable
26
Powering the PDU and Controller
27
Supply Power to the PDU
27
Switch on the Controller
27
Configuring the System to a Network
28
Installing a Support Bay and Instrument Rack
29
Introduction
29
Install the Testhead Module Umbilical Cable(S) (307X Only)
29
Install the GPIB Cables (307X Only)
30
Setting-Up Other Hardware
33
Install a Pay-Per-Use (PPU) Button Adapter
33
Setup the Testhead for Automation
36
Install Accessplus Cables
38
Enabling the Testhead
39
Boot the Testhead
39
Troubleshooting Testhead Boot
39
Check the System Config File
40
Verifying the Vacuum Subsystem
42
Introduction
42
Install the Vacuum Manifold
42
Connect the Compressed Air
42
Check the Vacuum Actuation System
42
Troubleshooting
43
Verifying the Testhead
45
Run Autoadjust All
45
Run Full Diagnostics
45
Completing the Installation
46
Verify Strip Printer
46
System Printer / Plotter
46
Stabilize the Testhead
46
Reinstall Covers
46
Make System Recovery and Backup Tapes
46
Turn System Administration over to the Customer
46
Fill out the System Support Log
46
Maintenance Records
47
About Scanworks
47
Installation Billing Information
47
In Case of Difficulty
48
Shipping Damage or Incorrect Shipment
48
Network, System Administration, or Test Server Help
48
Optional Agilent Performance Port Actuator Control System (ACS)
48
Vacuum Subsystem
48
Additional Resources
48
MS Windows System Installation Reference
49
In this Chapter
49
Referenced Manuals
49
Introduction
49
Logging-On as Service3070
50
Display the Logon Status from a Current Login
50
The Root Directory Environment Variable
51
Introduction
51
Determine the Value of the Root Directory Environment Variable
51
Use of the Root Directory Environment Variable in a BT-BASIC Window
52
Use of the Root Directory Environment Variable in a Korn Shell Window
53
Use of the Root Directory Environment Variable in a DOS Command Prompt Window
54
Directory Descriptions
55
Editing Files
56
Front-Slashes Versus Back-Slashes in Command Lines Containing File Paths
56
Use BT-BASIC
56
How to Edit the System Config File to Match the Testhead Configuration
56
How to Resolve the Standard Config File from the System Config File
56
MS Windows Quick Reference
63
Commonly Used Bt-Basic Statements
64
BT-BASIC Quick Reference
64
Korn Shell Quick Reference
65
And VI Editor Quick Reference
68
Codewords & Software License Keys
72
Introduction
72
Installing Codewords & Software License Keys
72
Verify Installed Codewords
72
Compile the Two Config Files
72
System Config File Specifics
74
Introduction
74
Location of the System Config File
74
Edit the System Config File
74
The "Official" and "Actual" System Config Files
74
To Repair a Corrupt System Config File
74
Descriptions of some Statements in the System Config File
74
Standard Config File Specifics
77
Introduction
77
Location of the Standard Config File
77
The Board Config File
77
Standard Config File Syntax Similarities to and Differences from the System Config File2-29
77
Statements Allowed in the Standard, System, and Board Config Files
78
Statements Allowed in the System Config File
78
Descriptions of some Statements in the Standard Config File
78
Compiling the System and Standard Config Files
83
The Bootptab File
84
Hardware Addresses
84
IP Addresses
85
The Hosts File
86
Test Device Communication
86
Device Files
88
Introduction
88
Location of Device Files
88
If a DUT Power Supply Is Replaced
88
DUT Power Supply Device Files
88
Vacuum Control
89
Location of Vacuum Control Statements
89
Vacuum Control Specifics
89
Rotating the Testhead
90
Testhead Cards
91
If Changing a Controlxt/Xtp or System Card
91
DUT Power Supplies
93
Voltage Ranges
93
DUT Power Supplies Allowed
93
Module Mappings
93
GPIB Addresses and Device Files
94
Controller Cables and Devices
97
X2000 Controller
98
X2100 Controller
101
Private LAN and Serial Port MUX
107
Introduction
107
IP Addresses
107
Hardware Addresses
107
Verify Communication to the Testhead
107
Serial Port MUX
107
Troubleshooting LAN Port Connections
109
Simple Solution
109
Setting the LAN Connection Properties
109
Installing Drivers and Configuring LAN Ports
110
Installing the Graphics and LAN Drivers
110
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Agilent Technologies 3070 and is the answer not in the manual?
Ask a question
Agilent Technologies 3070 Specifications
General
Brand
Agilent Technologies
Model
3070
Category
Test Equipment
Language
English
Related product manuals
Agilent Technologies 3070 Series
410 pages
Agilent Technologies 3000 Series
122 pages
InfiniiVision 3000
424 pages
InfiniiVision 3000 X-Series
440 pages
InfiniiVision 3000 MSO-X 3012A
424 pages
InfiniiVision 3000 DSO-X 3014A
424 pages
InfiniiVision 3000 DSO-X 3024A
424 pages
Agilent Technologies N9310A
188 pages
Agilent Technologies E6198B
318 pages
Agilent Technologies HP 83711B
251 pages
Agilent Technologies HP 83712B
251 pages
Agilent Technologies 8960 Series
165 pages
Need help?
General
To Previous Page