125
A II. ADJUSTMENT
MARGINS TABLES
Main voltage measurement points
CIIM0015 Power supply board
TP1 - 6V [5.6-5.8] V
TP2 - 12V [11.7 -11.9] V
TP3 - 5V [4.9-5.2] V
Sp150 [23.5-24.5] V
CIIM0026 Microprocessor board
TP60 - Vref motor Z [13 -15] mV
TP61 - Vref motor Y [13 -15] mV
TP56 - Vref motor X [13 -15] mV
TP57 - Vref pump motor [13 -15] mV
TP58 - Vref lter motor [13 -15] mV
TP59 - Vref rotor motor [13 -15] mV
Main adjustment values of the analyzer
Tolerances
Operating arm positioning
X axis loss of steps
Loss of steps [-3,3]
Y axis loss of steps
Loss of steps [-3,3]
Z axis loss of steps
Loss of steps [-3,3]
Loss of steps rotor motor
Loss of steps [-3,3]
Loss of steps lter drum motor
Loss of steps [-3,3]
Loss of steps pump motor
Loss of steps [-4,4]
XY position adjustment
X origin [10,125]
Y origin [240,290]
X racks tray [620,750]
Y racks tray [-20,20]
X washing station [330,450]
Y washing station [70,120]
X rotor [60,170]
Y rotor [1030,1060]
Maximum Z [1090,1155]
Self-centering of needle
X Offset [-4,4]
Y Offset [-4,4]
Bottle level control sensitivity
Water empty [200,255]
Water full [140,230]
Water calculated [170,240]
Waste empty [200,255]
Waste full [170,245]
Waste calculated [200,245]
Level detection sensitivity
Paediatric rack [45,90]
13/15mm tube sample rack [45,90]
Reagent rack [25,45]
Positioning of the dispensing point
Dispensing rotor [90,120]
Fine rotor X [35,200]
Positioning of rotor in optic
Positioning [-15,0]
Needle thermostatation
Set point temperature [35,45]
Rotor thermostatation
Set point temperature [36,37.5]
Filter wheel positioning
Positioning [-5,5]
Integration times
F1 340 nm [190,350]
F2 405 nm [40,130]
F3 505 nm [40,130]
F4 535 nm [40,130]
F5 560 nm [40,130]
F6 600 nm [40,130]
F7 635 nm [40,130]
F8 670 nm [50,130]
Number of counts
F1 340 nm [750000,960000]
F2 405 nm [840000,940000]
F3 505 nm [840000,940000]
F8 670 nm [840000,940000]
Darkness counts
F1 340 nm [3700,4300]
F2 405 nm [3700,4300]
F3 505 nm [3700,4300]
F8 670 nm [3700,4300]
SMF repeatability (Noise)
Dev. Est. NC. F0 Covered ≤ 55
Dev. Est. Abs. F1 340 nm ≤ 0.0004
Dev. Est. Abs. F2 405 nm ≤ 0.0006
Dev. Est. Abs. F3 505 nm ≤ 0.0004
Dev. Est. Abs. F8 670 nm ≤ 0.0007
Stability at 505 nm
Dev. Est. Abs. F3 505 nm ≤ 0.0008
Max. NC [840000,940000]
Min. NC [840000,940000]
Max NC / Min NC ≤ 1,006
Repeatability MF (Repeatability)
Dev. Est. Abs. F1 340 nm ≤ 0.0008
Dev. Est. Abs. F2 405 nm ≤ 0.0006
Dev. Est. Abs. F3 505 nm ≤ 0.0005
Dev. Est. Abs. F4 535 nm ≤ 0.0005
Dev. Est. Abs. F5 560 nm ≤ 0.0005
Dev. Est. Abs. F6 600 nm ≤ 0.0005
Dev. Est. Abs. F7 635 nm ≤ 0.0005
Dev. Est. Abs. F8 670 nm ≤ 0.0005
To Next Page
Loading...