EasyManua.ls Logo

Buffalo BS-GS2016 - User Manual

Buffalo BS-GS2016
93 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Layer2 Gigabit Smart Switch
BS-GS20 Series
BS-GS20P Series
User Manual
Americas: www.buffaloamericas.com
Europe: www.buffalo-technology.com
35020643-07
2018.10

Table of Contents

Questions and Answers

  • K
    Kyle SmithAug 18, 2025
    How to access settings of Buffalo BS-GS2016 Switch?
    • S
      Susan MartinAug 18, 2025
      If you're having trouble accessing the settings of your Buffalo Switch, here are some steps you can take: 1. First, ensure that your PC is properly connected to the switch. 2. Try accessing the settings using the switch's IP address, which is 192.168.1.254 by default. 3. Confirm that you are using the correct username ("admin" by default) and password ("password" by default). If you've forgotten these, you may need to initialize the switch. 4. If you have a proxy server configured in your web browser, try disabling it or adding the switch's IP address to the proxy server's exception list. 5. Finally, ensure that your PC is connected to the port that belongs to the management VLAN.
  • P
    Paul CruzAug 28, 2025
    What to do if I forgot the password for Buffalo BS-GS2016 Switch?
    • S
      Stacy DavisAug 29, 2025
      If you've forgotten the password for your Buffalo Switch, the default password is 'password'. If you have changed it, you can press the reset button to initialize the switch. If the physical reset button is disabled and you forgot the password of Settings, contact our technical support.
  • C
    Christopher Day DVMNov 7, 2025
    What to do if LED is not lit, abnormal lighting or blinking on Buffalo BS-GS2016 Switch?
    • P
      Patricia MendezNov 8, 2025
      If the LED on your Buffalo Switch isn't lit, shows abnormal lighting, or is blinking, here are a few things to check: * Ensure the AC adapter or power cable is properly connected to the inlet. * Make sure the Ethernet cable is connected securely to both the switch and the device. * Verify that both the switch and the connected device are powered on. * Confirm the Ethernet cable type and length are compatible with the switch. If it blinks once per a second, a loop is detected, so check the cabling. If your switch has fans and its diag LED is blinking fast, a fan error may be occurring. Disconnect the power cable and reconnect it. If the LED keeps blinking, contact our technical support. Confirm whether the physical reset button is enabled in Settings. If the physical reset button i...

Summary

Chapter 1 Initial Settings

Change Switchs IP Address

Procedure to change the switch's IP address to match your PC's segment.

Open Settings

Procedure to access the switch's web admin interface.

Change Username and Password

Guide to changing the default admin credentials.

Chapter 2 Settings

VLAN Settings

Confirm VLAN status and create new VLANs for network segmentation.

SNMP Settings

Configure SNMP community tables, host tables, and traps.

Static MAC Filtering

Configure filtering of MAC addresses registered manually.

Dynamic MAC Filtering

Set MAC address learning limits for each port.

Administration Account

Configure the switch's username and password.

PoE Status

Displays the Power over Ethernet status for each port.

QoS Settings

Configure Quality of Service priority settings.

IPv4;MAC Policy

IPv6 Policy

Auto DoS Attack Prevention

DHCP Snooping

RADIUS

Port Authentication

Spanning Tree Protocol

ACL Wizard

Loop Prevention

Update Firmware

Update the switch firmware from a local file.

Back Up and Restore Settings

Save and restore the switch's configuration settings.

Network Diagnostics

Cable Diagnostics

Chapter 3 Troubleshooting

LED Status Issues

Troubleshoot issues related to power, diag, and link/act LEDs.

Cannot Access Settings

Resolve problems preventing access to the switch's configuration interface.

Forgot the Password

Procedures for recovering or resetting forgotten credentials.

Appendix A Specifications

Backing Up and Restoring Settings

Save and restore the switch's configuration settings.

Technical Support

Buffalo BS-GS2016 Specifications

General IconGeneral
BrandBuffalo
ModelBS-GS2016
CategorySwitch
LanguageEnglish

Related product manuals