Digi CM 8 - Page 130

190 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Power Controller Cascade multiple Digi RPM units

Digi CM User Guide 130

Table of Contents

Default Chapter3
- Table of Contents3
Overview10
- Digi CM Model Support10
  - Feature Overview10
- Feature Summary10
- User Groups12
- Root and Admin Usernames and Passwords12
- Adding Port Administrators and Users12
- Access Lists12
- Ways to Configure the Digi CM12
- Ways of Accessing the Digi CM Ports: Overview14
- Web Interface Access Menu14
- Port Access Menu16
- Direct Port Access17
- Custom Menus17
- Port Escape Menu17
  - Description of Fields19
Snmp19
- Save and Apply Changes19
  - One Step: Save and Apply Changes19
  - Two-Step: Save to Flash and then Apply Changes20
- Locater Light20
Getting Started22
- Introduction22
- Assigning IP Settings from the Console Port22
- Configure for SSH23
- Add, Edit, and Remove Users25
  - Procedure25
  - About Shell Options26
Install and Configure PC Cards28
- Introduction28
- Compatible PC Cards28
- Add a Compact-Flash Card28
- Add a Network Card29
- Add a Wireless LAN Card30
- Add a Serial Modem31
System Status and Port Logging34
- Introduction34
- System Status & Log34
- Enable the Log Storage Location35
- Configure System Logging39
  - View System Logs40
- Configure Port Logging40
  - View Port Logs42
Configure Ports44
- Introduction44
- Enable and Disable the Ports44
- Realport Support44
- Resetting Ports45
  - Reset Individual Port Settings45
- Port Title45
- Configure Automatic Device Recognition46
- Apply All Ports Settings47
- Host Mode Configuration48
- Configure Host Mode51
- Supported Protocols52
- Serial Port Parameters52
- DTR Behavior53
  - Inter-Character Timeout53
- Specialty Use of Port -When Data Is Processed in Chunks53
- Remote Ports54
  - Configure Remote Ports54
  - Access a Remote Port54
Alerts and Notifications57
- Introduction57
- Configuring SMTP Alerts57
- SNMP Information58
- Traps58
- Configure SNMP59
- Manage the SNMP Protocol60
- Configure Port Event Handling60
- Configure Alerts for Automatic Device Recognition (ADR)62
User Administration63
- Administer Users64
Configure Security and Authentication68
- Introduction68
- Configure Network IP Filtering68
- Configure User Access Control72
- Security Profile76
  - System Security77
  - Password Security77
- Authentication78
- Configure Authentication Methods for Port Access79
- Configure Authentication for the Web Server80
Custom and Default Menus82
- Introduction83
- Make Custom Menus83
- Default Menu86
  - Port Access Menu86
Microsoft SAC Support89
- About the Digi CM Unit's Support for Microsoft Windows Server 200389
  - Setup Overview89
- Setup the Windows Server 2003 Port90
  - Command Syntax90
  - Command Example90
- Setup the Digi CM Unit for SAC Support90
- Access the Windows Server 2003 Console Port from the Digi CM Unit's GUI92
Configure Virtual KVM95
- Introduction95
  - An Example Configuration95
  - Virtual KVM Protocols95
- Use Virtual KVM with Remote Desktop Protocol96
  - Configure96
  - Connect to a System through Virtual KVM Using Remote Desktop Protocol98
- Use Virtual KVM with VNC Protocol99
  - Configure99
  - Connect to a System through Virtual KVM Using VNC101
- Use Virtual KVM with X Window System Protocol and Xmanager Software102
  - Configure103
  - Connect to a System through Virtual KVM Using Xmanager104
- Virtual KVM Assistant105
  - How the Virtual KVM Assistant Works106
  - User Client PC Platforms Supported106
- Install Programs for Virtual KVM106
Rackable Systems Management Card109
- Introduction110
- Setup the Digi CM Unit to Support the Rackable Systems Management Card110
Rackable Systems Management Card111
- Introduction115
- Configure for Dial-In Modem Access115
- Add a PC Modem118
- Configure for Dial-In Terminal Server Access118
Power Controller121
- Introduction121
- Install Power Controller122
- Configure Power Controller122
  - Configure the Serial Port Parameters to Match the Power Controller122
  - Add the Power Controller122
- Set Alarms and Thresholds123
- Outlet Configuration124
- User Access for Power Controller125
  - Configure to Allow Specific Users Access125
  - Configure to Restrict Specific Users126
- Power Controller Management127
- Cascade Multiple Digi RPM Units128
Port Clustering131
- Introduction132
- Configure Port Clustering132
System Administration137
- Introduction138
- Upgrade the Firmware138
  - Web Interface138
- Configuration Management138
  - Save the Configuration Automatically139
- Automatically Upgrade the Digi CM Unit's Firmware or Configuration Using TFTP140
- Reset Factory Defaults143
- Set the Date and Time144
- Configure a Host Name144
Command Line Interface147
- Introduction147
- Linux Commands147
- Important File Locations148
- Example Scripts150
- User Administration152
  - Locator LED Script152
Configuration Menu154
- Introduction to the Configuration Menu155
- Access the Configuration Menu155
- Configure SSH155
- Add, Edit, and Remove Users156
- Add and Configure a PC Card156
- Host Mode Configuration157
- Port Parameters158
- Port Access Menu158
- System Logging159
  - Configure the System Log Device159
  - Configure System Logging160
- Configure SNMP160
- Configure SMTP161
- Network IP Filtering161
- Port IP Filtering162
- Sniff Sessions163
  - View a Sniff Session164
  - Field Descriptions for Sniff Sessions164
- Authentication165
- Upload Server Certificate166
  - Openssl(Ssleay) Simple CA Usage - Install Openssl166
  - Make Root CA (Certificate Authority for Self-Signed)166
  - Make a Certificate Request167
  - Sign a Certificate Request168
  - Make Certificate for the Digi CM Unit169
- Dial-In Modem Access170
- Dial-In Terminal Server Access170
- Clustering171
- Firmware Upgrade172
- Restore Factory Defaults173
- Set the Date and Time174
- Access the Boot Loader Program174
  - Hardware Test Menu174
  - Disaster Recovery174
Hardware Information177
- Introduction178
- Hardware Specifications178
- LED Indicators180
- About Serial Port Cabling180
- Serial Port Pinouts181
- Cable Adapters181
- Ethernet Pinouts185
- Rack Mounting Installation186
  - Rack Mounting Safety Precautions186
Certifications187
Safety188
- Working Inside the Digi CM Unit188
- Replacing the Battery188
- Remplacer la Batterie188
- Rack Mounting Installation Considerations188
- Environmental Considerations and Cautions189
- Safety Instructions189
- Power and Ground - Digi CM 48 Single and Dual Power190
- Emissions190
- Immunity190
- Solaris Ready190

Related product manuals

Preview: Digi CM Series

Preview: Digi Connect ME

Digi Connect ME