© Edwards Limited 2015. All rights reserved. Page iii
Edwards and the Edwards logo are trademarks of Edwards Limited.
Contents
M588-00-880 Issue E
A2.4.7 Software version display menu ..................................................................................... 111
A2.4.8 Display serial number ................................................................................................ 111
A2.4.9 Fit accessory menu ................................................................................................... 112
A2.4.10 IP configuration menu ................................................................................................ 113
A2.4.11 Display menu .......................................................................................................... 113
A2.4.12 Set clock ...............................................................................................................114
A2.5 How to set up the PDT display ...................................................................................... 115
A2.5.1 Setting the status screen to automatically scroll ................................................................ 115
A2.5.2 Change the normal menu display ................................................................................... 115
A2.6 How to configure the pump warm-up options .................................................................... 116
A2.6.1 Lowering the warm-up temperature ............................................................................... 116
A2.6.2 Disabling warm-up cycle ............................................................................................. 116
A2.6.3 Increasing the warm-up temperature ............................................................................. 117
A2.6.4 Stop the pump going on-process when it is warm ............................................................... 117
A2.6.5 Stop the pump automatically warming up when in Green Mode / standby mode .......................... 117
A2.6.6 Turn inlet purge on during warm-up ............................................................................... 117
A2.6.7 Allow a pump to go on-process with a warning .................................................................. 117
A2.6.8 Warm soft start ....................................................................................................... 117
A2.7 How to configure the booster pump behaviour .................................................................. 117
A2.7.1 Setting the booster to manual operation ......................................................................... 118
A2.7.2 Changing the booster time delay ................................................................................... 118
A2.7.3 Setting the booster to start when the inlet isolation valve is open ........................................... 118
A2.8 How to configure pump behaviour ................................................................................. 119
A2.8.1 Smart stop ............................................................................................................. 119
A2.8.2 How to configure ramped speed increase ........................................................................ 120
A2.9 How to set up DP clean .............................................................................................. 121
A2.9.1 Changing the dry pump speed during the clean operation ..................................................... 123
A2.9.2 Changing the clean cycle time ...................................................................................... 124
A2.9.3 Automatically initiating a clean cycle when the pump goes off-process .................................... 124
A2.9.4 Turn inlet purge on during the clean cycle ....................................................................... 124
A2.9.5 Have inlet purge cycle after clean cycle .......................................................................... 124
A2.9.6 Allow on process ...................................................................................................... 124
A2.9.7 Auto on shutdown ..................................................................................................... 124
A2.10 How to control pump speed ......................................................................................... 124
A2.10.1 Normal speed .......................................................................................................... 125
A2.10.2 External voltage ...................................................................................................... 126
A2.10.3 SIM protocol ........................................................................................................... 126
A2.10.4 Second speed control ................................................................................................ 126
A2.10.5 Profibus interface ..................................................................................................... 126
A2.11 How to use PID pressure control .................................................................................... 127
A2.11.1 Fit and configure the pressure sensor ............................................................................. 128
A2.11.2 Using a different gauge .............................................................................................. 129
A2.11.3 Set pump into Green Mode mode .................................................................................. 129
A2.11.4 Enable PID ............................................................................................................. 129
A2.11.5 Set the PID target pressure set point ............................................................................. 130
A2.11.6 Test the PID control .................................................................................................. 130
A2.11.7 Auto tune the PID ..................................................................................................... 130
A2.11.8 Manually tuning the PID .............................................................................................. 130
A2.11.9 Turning PID on and off when on-process .......................................................................... 130
A2.12 How to set up the Ethernet port ................................................................................... 131
A2.12.1 Using SIM protocol through Ethernet .............................................................................. 133
A2.12.2 Web server pages ..................................................................................................... 135
A2.13 How to use SIM protocol with a serial port ....................................................................... 138
A2.14 How to set up the MCM MicroTIM using the PDT ................................................................. 139
A2.14.1 Configuring the channel 2 input .................................................................................... 140
A2.14.2 Configuring the channel 4 output .................................................................................. 141
A2.15 How to run the booster independently from the dry pump .................................................... 141
A2.15.1 Run the booster manually using the PDT .......................................................................... 141
A2.15.2 Run the booster using SIM and Profibus ........................................................................... 141
A2.15.3 Run the booster using the MCM MicroTIM ......................................................................... 141
Appendix A3 Troubleshooting ......................................................................... 143
To Next Page
Loading...
