Emerson Rosemount 5402 - Double Bounce Echo Management

To Next Page

To Previous Page

Product Certifications

October 2018

Reference Manual

00809-0100-4026, Rev KC

Product Certifications

256

Main Page

Table of Contents3
Using this Manual15
Product Recycling/Disposal16
Theory of Operation17
Application Examples18
System Architecture20
Process Characteristics22
Components of the Transmitter24
Antenna Selection Guide/Measuring Range25
Safety Messages29
Installation Procedure31
Mounting Considerations32
Mounting Location32
Special Considerations in Solids Applications34
Mounting in Pipes35
Condensation Conditions36
Nozzle Considerations37
Nozzle Recommendations and Requirements41
Service Space45
Beam Width46
Vessel Characteristics48
Disturbing Objects48
Valves48
Mounting49
Cone Antenna with Flange Connection49
Cone Antenna with Threaded Tank Connection50
Cone Antenna with Threaded Tank Connection and Customer Supplied Flange52
Process Seal Antenna with Flange60
Parabolic Antenna with Flange62
Parabolic Antenna with Welded Connection64
Parabolic Antenna with Threaded Connection71
Adjust Inclination of Parabolic Antenna77
Rod Antenna with Threaded Connection81
Rod Antenna with Flanged Connection82
Tri Clamp Tank Connection83
Bracket Mounting84
Safety Messages85
Wiring and Power Supply Requirements87
Cable/Conduit Entries87
Grounding87
Cable Selection88
Hazardous Areas88
External Circuit Breaker88
Connecting the Transmitter89
HART ® Communication92
Power Requirements92
Load Limitations92
Non-Intrinsically Safe Power Supply94
Intrinsically Safe Power Supply95
Type N Approvals: Non-Sparking/Energy-Limited Power Supply96
Transient Protection Terminal Block96
Foundation97
OUNDATION Fieldbus97
Power Requirements97
Non-Intrinsically Safe Power Supply99
Intrinsically Safe Power Supply100
Type N Approvals: Non-Sparking/Energy-Limited Power Supply101
HART to Modbus Converter (HMC)102
Connecting the Transmitter102
Connection Terminals104
Bus105
Installation Cases105
External HART Devices (Slaves)107
Establish HART Communication108
Connect to the MA/MB Terminals108
Connect to the HART Terminals110
Optional Devices111
1Tri-Loop™ HART to Analog Converter111
Field Signal Indicator111
Emerson ™ Wireless THUM ™ Adapter112
Safety Messages113
Overview114
Basic Configuration Parameters114
Configuration Tools114
Basic Configuration Parameters115
Measurement Units115
Tank Geometry115
Process Conditions117
Volume Configuration118
Analog Output (HART)121
Level and Distance Calibration122
Echo Tuning123
Atc124
Basic Configuration Using RRM124
System Requirements124
Help in RRM125
Installing the RRM Software for HART Communication125
Specifying the COM Port126
Setting the COM Port Buffers127
Specifying Measurement Units127
Installing the RRM Software for FOUNDATION Fieldbus127
Specifying Measurement Units129
Using the Setup Functions130
Guided Setup131
Using the Setup Functions142
Configuration Using a Field Communicator143
Basic Configuration Using AMS Suite147
Configuration Using Deltav148
Advanced Configuration153
Foundation154
Assigning Device Tag and Node Address155
FOUNDATION Fieldbus Block Operation155
Application Examples157
Radar Level Transmitter - Level Value157
Radar Level Transmitter - Level Value in Percent (%)158
Tri-Loop™ HART to Analog Converter159
HART Multidrop Configuration161
Safety Messages163
Viewing Measurement Data165
Using the Display Panel165
Specifying Display Panel Variables165
Viewing Measurement Data in RRM168
Viewing Measurement Data in AMS Suite and Deltav170
LCD Display Error Messages171
LED Error Messages172
Safety Messages173
Troubleshooting Overview175
Service Overview176
Analyzing the Measurement Signal176
Surface Pulse Not Found177
Registration of False Echoes178
Using the Echo Curve Analyzer180
Using the Echo Curve Analyzer with a Field Communicator183
Analog Output Calibration185
Logging Measurement Data186
Backing up the Transmitter Configuration187
Diagnostics188
Configuration Report189
Viewing Input and Holding Registers190
Reset to Factory Settings191
Surface Search192
Using the Simulation Mode193
Write Protecting a Transmitter194
Diagnostic Messages195
Troubleshooting195
Device Status195
Errors196
Warnings197
Measurement Status197
Volume Calculation Status199
Analog Output Status200
Application Errors201
Troubleshooting205
Resource Block206
Transducer Block207
Analog Input (AI) Function Block208
Service Support210
Safety Messages211
Overview212
Applicable Models212
Skill Level of Personnel212
Functional Specifications213
Installation213
Configuration215
Damping215
Alarm and Saturation Levels215
Amplitude Threshold216
Write Protection216
Site Acceptance216
Operation and Maintenance216
General216
Inspection217
References218
Specifications218
Failure Rate Data218
Useful Lifetime218
Spare Parts218
Terms and Definitions218
Aappendix A: Specifications and Reference Data219
Functional Specifications219
General219
4-20 Ma HART® (Output Option Code H)219
FOUNDATION ™ Fieldbus (Output Option Code F)221
Rosemount 2410 Tank Hub Connectivity (Output Option Code U)222
With Modbus Communication (Output Option Code M)222
Display and Configuration223
Diagnostics224
Temperature Limits224
Process Temperature and Pressure225
Performance Specifications226
General226
Measuring Range226
Solids Applications229
Environment230
Physical Specifications230
Material Selection230
Housing and Closure230
Engineered Solutions231
Tank Connection and Antennas231
Dimensional Drawings and Mechanical Properties233
Process Connections239
Ordering Information241
European Directive Information253
Ordinary Location Certification253
Fcc253
Radio Equipment Directive (RED)254
Installing Equipment in North America254
Usa254
Canada255
Europe256
International258
Brazil259
China260
Technical Regulations Customs Union (EAC)261
Japan261
India261
Ukraine261
Uzbekistan261
Republic of Korea262
Combinations262
Additional Certifications262
Pattern Approval262
Conduit Plugs and Adapters263
Approval Drawings263
Safety Messages269
Tank Geometry270
Distance Offset (G)270
Minimum Level Offset (C)270
Hold off Distance271
Calibration Distance271
Advanced Analog Output Settings271
Advanced Transmitter Settings272
Antenna Type272
Empty Tank Handling272
Full Tank Handling273
Double Bounce273
Surface Echo Tracking274
Filter Settings275
Advanced Functions in RRM276
Empty Tank Handling276
Full Tank Handling279
Double Bounce280
Surface Echo Tracking281
Hold off Setting282
Signal Quality Metrics (SQM)283
Available Diagnostics Measurements283
How to Verify if Signal Quality Metrics Is Supported284
View Signal Quality Metrics Values in RRM285
Performing Proof Test287
Field Communicator287
Rrm289
AMS Suite291
Overview293
Definition293
Channel Definitions293
Supported Units301
Unit Codes301
Diagnostics Device Errors302
Overview311
Parameters and Descriptions311
Alarm Priority320
Recommended Actions for Plantweb Alerts321
Overview323
Block Errors328
Modes328
Alarm Detection329
Status Handling330
Configure the AI Block330

Emerson Rosemount 5402 - Double Bounce Echo Management

Table of Contents

Related product manuals