ESAB 100i - Page 156

TORCH DATA 100i-400i 156 Manual 0560956430
Stainless Steel
Flow Rates (SLPM / SCFH)
150A
H35 N₂
Preow
- / - 55 / 117
H35 Plasma / N₂ Shield
Culow
16 / 33 37 / 78
Electrode
Shield Cap
Tip
Shield Gas
Distributor
Plasma Gas
Distributor
Cartridge
Shield Cup
This Art Is For Reference ONLY
Art # A-07958_AB
Shield Cup Shield Cap
Shield Gas
Distributor
Tip Plasma Gas Distributor Electrode Cartridge
0559211201 0559210146 0559210081 0559210127 0559210061 0559210108 0559211200
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Arc
Voltage
Cut Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (H35) Shield (N₂)
ga (in) inch (psi) Ball (psi) Ball (psi) (Volts) (in) ±0.005 (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
- 1/2 0.500 84 57 120 85 120 153 0.300 0.5 0.250 0.200 0.4 0.350 50 0.2 0.110
- 5/8 0.625 84 57 120 85 120 155 0.200 0.9 0.250 0.200 0.2 0.350 40 0.4 0.118
- 3/4 0.750 84 57 120 85 120 157 0.225 1.4 0.300 0.250 0.2 0.400 30 0.6 0.128
- 7/8 0.875 84 57 120 85 120 161 0.238 2.4 0.325 0.250 0.2 0.425 25 1.2 0.131
- 1 1.000 84 57 120 85 120 165 0.250 3.6 0.350 0.300 0.2 0.450 20 1.8 0.133
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Arc
Voltage
Cut Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (H35) Shield (N₂)
(mm) (Bar) Ball (Bar) Ball (Bar) (Volts) (mm) ±0.1 (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
12 5.8 57 8.3 85 8.3 153 8.2 0.4 6.4 5.1 0.4 8.9 1330 0.2 2.7
15 5.8 57 8.3 85 8.3 154 5.8 0.8 6.4 5.1 0.3 8.9 1090 0.3 2.9
20 5.8 57 8.3 85 8.3 158 5.8 1.7 7.8 6.4 0.2 10.4 720 0.8 3.3
25 5.8 57 8.3 85 8.3 164 6.3 3.4 8.8 7.5 0.2 11.4 520 1.7 3.4
Marking
Pre Flow
Pressure
(N₂)
Marking Flow Rates /
Pressures
Arc
Voltage
Marking
Height
Pierce Ignion Height
THC and CNC
Delay
Control
Delay
Travel
Speed
Marking quality
degrades as
thickness
decreases.
19A Arc Current
Plasma (N₂) Shield (N₂)
Burn-through may
happen for thicknesses
< 1/16” (0.063”) /
1.6 mm.
(psi) /
(Bar)
Ball
(psi) /
(Bar)
Ball
(psi) /
(Bar)
(Volts)
(in) ±0.005 /
(mm) ±0.1
(in) ±0.005 / (mm) ±0.1 (sec) (sec)
(ipm) /
(mm/ min)
20 / 1.4 60
60 /
4.1
75
80 /
5.5
130 0.120 / 3.0 0.120 / 3.0 0 0.4
300 /
7620
BOLD TYPE indicates maximum piercing parameters.