ESAB 100i - Robotic and Bevel Cutting 150 - 200 Amp

Manual 0560956430 167 TORCH DATA 100i-400i
Mild Steel
Flow Rates (SLPM / SCFH)
200A Bevel Cut
O₂ Air
Preow
- / - 162 / 343
O₂ Plasma / Air Shield
Culow
102 / 217 133 / 281
Cartridge
Electrode
Shield
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Shield Retainer
Art # A-07917_AC
This Art Is For Reference ONLY
Shield Retainer Shield Cap
Shield Gas
Distributor
Tip Plasma Gas Distributor Electrode Cartridge
0559211210 0559210047 0559210073 0559210026 0559210062 0559210005 0559211300
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(Air)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (O₂) Shield (Air)
inch (in) (psi) Ball (psi) Ball (psi) (in) (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
0.188 0.080 15 100 100 NA 100 0.130 - 0.550 0.2 0.200 0.150 0.5 0.300 250 0.2 0.142
0.250 0.080 15 100 100 NA 100 0.130 - 0.550 0.2 0.200 0.150 0.5 0.300 200 0.2 0.148
0.375 0.080 15 100 100 NA 100 0.150 - 0.550 0.3 0.250 0.200 0.5 0.350 140 0.3 0.162
0.500 0.080 15 100 100 NA 100 0.170 - 0.550 0.7 0.250 0.200 0.5 0.350 115 0.5 0.167
0.625 0.080 15 100 100 NA 100 0.200 - 0.550 0.9 0.250 0.200 0.5 0.350 80 0.6 0.186
0.750 0.080 15 100 100 NA 100 0.200 - 0.550 1.3 0.300 0.250 0.5 0.400 65 0.8 0.186
0.875 0.080 15 100 100 NA 100 0.200 - 0.550 1.6 0.300 0.250 0.5 0.400 57 1.0 0.185
1.000 0.080 15 100 100 NA 100 0.200 - 0.550 1.9 0.300 0.250 0.5 0.400 48 1.2 0.193
1.250 0.080 15 100 100 NA 100 0.200 - 0.550 3.2 0.325 0.250 0.5 0.425 30 2.0 0.196
1.500 0.080 15 100 100 NA 100 0.200 - 0.550 5.8 0.350 0.300 0.5 0.450 20 4.0 0.201
1.750 0.080 15 100 100 NA 100 0.200 - 0.550 1.0 Edge Start 0.5 Edge 15 1.0 0.203
2.000 0.080 15 100 100 NA 100 0.200 - 0.550 1.0 Edge Start 0.5 Edge 10 1.0 0.204
2.500 0.080 15 100 100 NA 100 0.200 - 0.550 1.0 Edge Start 0.5 Edge 8 1.0 0.210
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(Air)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (O₂) Shield (Air)
(mm) (mm) (Bar) Ball (Bar) Ball (Bar) (mm) (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
5 2.0 1.0 100 6.9 NA 6.9 3.3 - 14.0 0.2 5.1 3.8 0.5 7.6 6170 0.2 3.6
6 2.0 1.0 100 6.9 NA 6.9 3.3 - 14.0 0.2 5.1 3.8 0.5 7.6 5360 0.2 3.7
8 2.0 1.0 100 6.9 NA 6.9 3.6 - 14.0 0.3 5.7 4.5 0.5 8.3 4290 0.3 3.9
10 2.0 1.0 100 6.9 NA 6.9 3.9 - 14.0 0.4 6.4 5.1 0.5 8.9 3460 0.3 4.1
12 2.0 1.0 100 6.9 NA 6.9 4.2 - 14.0 0.6 6.4 5.1 0.5 8.9 3060 0.5 4.2
15 2.0 1.0 100 6.9 NA 6.9 4.9 - 14.0 0.8 6.4 5.1 0.5 8.9 2280 0.6 4.6
20 2.0 1.0 100 6.9 NA 6.9 5.1 - 14.0 1.4 7.6 6.4 0.5 10.2 1590 0.9 4.7
25 2.0 1.0 100 6.9 NA 6.9 5.1 - 14.0 1.9 7.6 6.4 0.5 10.2 1250 1.2 4.9
30 2.0 1.0 100 6.9 NA 6.9 5.1 - 14.0 2.8 8.1 6.4 0.5 10.6 890 1.8 5.0
35 2.0 1.0 100 6.9 NA 6.9 5.1 - 14.0 4.5 8.6 7.0 0.5 11.1 630 3.0 5.0
40 2.0 1.0 100 6.9 NA 6.9 5.1 - 14.0 1.0 Edge Start 0.5 Edge 470 1.0 5.1
50 2.0 1.0 100 6.9 NA 6.9 5.1 - 14.0 1.0 Edge Start 0.5 Edge 270 1.0 5.2
60 2.0 1.0 100 6.9 NA 6.9 5.1 - 14.0 1.0 Edge Start 0.5 Edge 220 1.0 5.3
BOLD TYPE indicates maximum piercing parameters. BOLD ITALIC indicates edge starts only.
8.04 Robotic and Bevel Cutting 150 - 200 Amp