ESAB 100i - Bevel and Robotic Cutting up to 100 Amp

Manual 0560956430 147 TORCH DATA 100i-400i
Mild Steel
Flow Rates (SLPM / SCFH)
100A Bevel Cut
O₂ Air
Preow
- / - 38 / 81
O₂ Plasma / Air Shield
Culow
16 / 35 27 / 58
Shield Cup Shield Cap
Shield Gas
Distributor
Tip Plasma Gas Distributor Electrode Cartridge
0559211201 0559211127 0559210081 0559210033 0559210061 0559210012 0559211200
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(Air)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (O₂) Shield (Air)
inch (in) (psi) Ball (psi) Ball (psi) (in) (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
0.135 0.080 40 55 120 35 120 0.070 - 0.250 0.2 0.125 0.120 0.6 0.200 280 0.2 0.065
0.188 0.080 40 55 120 35 120 0.090 - 0.250 0.2 0.125 0.120 0.6 0.200 190 0.2 0.070
0.250 0.080 40 55 120 35 120 0.100 - 0.250 0.3 0.125 0.120 0.5 0.200 150 0.3 0.078
0.375 0.080 40 55 120 35 120 0.110 - 0.250 0.4 0.150 0.150 0.4 0.250 95 0.4 0.085
0.500 0.080 40 55 120 40 120 0.120 - 0.250 0.6 0.200 0.150 0.4 0.300 68 0.6 0.097
0.625 0.080 40 55 120 40 120 0.120 - 0.250 0.8 0.250 0.200 0.4 0.350 55 0.8 0.100
0.750 0.080 40 55 120 40 120 0.150 - 0.250 3.5 Edge Start 0.4 Edge 25 2.0 0.125
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(Air)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (O₂) Shield (Air)
(mm) (mm) (Bar) Ball (Bar) Ball (Bar) (mm) (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
4 2.0 2.8 55 8.3 35 8.3 2.0 - 6.4 0.2 3.2 3.0 0.6 5.1 6140 0.2 1.7
5 2.0 2.8 55 8.3 35 8.3 2.3 - 6.4 0.2 3.2 3.0 0.6 5.1 4680 0.2 1.8
6 2.0 2.8 55 8.3 35 8.3 2.5 - 6.4 0.3 3.2 3.0 0.5 5.1 4040 0.3 1.9
8 2.0 2.8 55 8.3 35 8.3 2.7 - 6.4 0.4 3.5 3.4 0.4 5.7 3080 0.4 2.1
10 2.0 2.8 55 8.3 36 8.3 2.8 - 6.4 0.4 4.0 3.8 0.4 6.5 2310 0.4 2.2
12 2.0 2.8 55 8.3 39 8.3 3.0 - 6.4 0.6 4.8 3.8 0.4 7.3 1880 0.6 2.4
15 2.0 2.8 55 8.3 40 8.3 3.0 - 6.4 0.7 6.0 4.7 0.4 8.5 1490 0.7 2.5
20 2.0 2.8 55 8.3 40 8.3 4.0 - 6.4 4.3 Edge Start 0.4 Edge 410 2.4 3.4
BOLD TYPE indicates maximum piercing parameters. BOLD ITALIC indicates edge starts only.
Electrode
Shield Cap
Tip
Shield Gas
Distributor
Plasma Gas
Distributor
Cartridge
Shield Cup
This Art Is For Reference ONLY
Art # A-09747
8.02 Bevel and Robotic Cutting Up To 100 Amp