ESAB 100i - Page 148

TORCH DATA 100i-400i 148 Manual 0560956430
Mild Steel
15A ROBOTIC COMPATIBLE
O
2
Plasma / O
2
Shield
Flow Rates (SLPM / SCFH)
O
2
Air
Preow
5 / 10 12 / 25
Culow 8 / 18 0 / 0
Shield Cup Shield Cap Shield Gas Distributor Tip Plasma Gas Distributor Electrode Cartridge
0559211201 0559210051 0559210091 0559210031 0559210090 0559210011 0559211200
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(Air)
Cut Flow Rates / Pressures
Arc
Voltage
Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon Delay
Max Kerf Width
@ Rec. Speed
Plasma (O
2
) Shield (O
2
)
ga (in) inch (psi) Ball (psi) Ball (psi) (Volts)
(in)
±0.005
(sec) (in) (in) (sec) (in) (ipm) (sec) (in)
26 - 0.024 70 35 100 20 40 108 0.030 0.0 0.080 0.050 1.5 0.100 185 0.0 0.042
26 - 0.024 70 35 100 20 40 117 0.030 0.0 0.080 0.050 1.5 0.100 95 0.0 0.050
20 - 0.036 70 35 100 20 40 110 0.040 0.0 0.080 0.050 1.5 0.100 150 0.0 0.043
20 - 0.036 70 35 100 20 40 120 0.040 0.0 0.080 0.050 1.5 0.100 80 0.0 0.052
18 - 0.048 70 35 100 20 40 114 0.040 0.1 0.080 0.050 1.5 0.100 110 0.1 0.049
18 - 0.048 70 35 100 20 40 125 0.040 0.1 0.080 0.050 1.5 0.100 60 0.1 0.057
16 - 0.060 70 35 100 20 40 119 0.060 0.2 0.080 0.050 1.5 0.100 75 0.2 0.056
14 - 0.075 70 35 100 20 40 126 0.080 0.2 0.080 0.050 1.5 0.100 55 0.2 0.070
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(Air)
Cut Flow Rates / Pressures
Arc
Voltage
Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon Delay
Max Kerf Width
@ Rec. Speed
Plasma (O
2
) Shield (O
2
)
(mm) (Bar) Ball (Bar) Ball (Bar) (Volts)
(mm)
±0.1
(sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
0.5 4.8 35 6.9 20 2.8 108 0.8 0.0 2.0 1.3 1.5 2.5 5100 0.0 1.1
0.5 4.8 35 6.9 20 2.8 116 0.8 0.0 2.0 1.3 1.5 2.5 2500 0.0 1.3
1 4.8 35 6.9 20 2.8 111 1.0 0.0 2.0 1.3 1.5 2.5 3500 0.0 1.1
1 4.8 35 6.9 20 2.8 122 1.0 0.0 2.0 1.3 1.5 2.5 1900 0.0 1.3
1.5 4.8 35 6.9 20 2.8 119 1.5 0.2 2.0 1.3 1.5 2.5 1900 0.2 1.4
2 4.8 35 6.9 20 2.8 129 2.0 0.2 2.0 1.3 1.5 2.5 1200 0.2 1.9
Note 1: Recommended with DFC-3000 automated gas console to improve cut quality at the start.
Note 2: Recommended for at plate, bevel and roboc cung applicaons.
Electrode
Shield Cap
Tip
Shield Gas
Distributor
Plasma Gas
Distributor
Cartridge
Shield Cup
This Art Is For Reference ONLY
Art # A-10272