Extron electronics XTP CrossPoint1600 - Page 106

XTP CrossPoint Series • Programming Guide 98
Command Function
SIS Command
(Host to Unit to Endpoint)
Response
(Endpoint to Unit to Host)
Additional Description
XTP T USW 103 and XTP T USW 103 4K switcher commands
Select an endpoint switcher input
Select an input
EX^
*
X5%
*3ETIE
}
Etie
X^
*
X5%
video
*
X5%
audio
]
Select input
X5%
on input
X^
.
The two
X5%
s are always the same.
Show selected input
EX^
ETIE
} X^
*
X5%
video
*
X5%
audio
]
Input video format (available for endpoint input 1 only)
Set format
X^
*
X2(
\ Ityp
X^
*
X2(
*
X3)]
Set input
X^
to
X2(
video format. The
endpoint reports the detected video
format,
X3)
, in the response.
Example:
1*0\
Ityp01*0*5
]
Set input 1 to auto. RGB is detected.
View format
X^
\
X2(
*
X3)]
View set (
X2(
) and detected (
X3)
) video
format of input
X^
.
Image reset (available for endpoint input 1 only)
Execute an image reset
E
T
X^
*1*2AADJ
}
AadjT1*1*2
]
Reset input 1 signal timing to default.
Pixel phase
NOTE: Pixel phase adjustments are available for RGBHV and non-interlaced component video (YUVp) video inputs.
Set a specific pixel sampling phase
E
I
X^
*
X3!
PHAS
}
PhasI
X^
*
X3!]
Specify the pixel sampling phase.
Increment sampling value
E
I
X^
+PHAS
}
PhasI
X^
*
X3!]
Increase the phase value.
Decrement sampling value
E
I
X^
–PHAS
}
PhasI
X^
*
X3!]
Decrease the phase value.
View the sampling value
E
I
X^
PHAS
} X3!]
Show the pixel sampling phase.
Horizontal shift (available for endpoint input 1 only)
Specify a value
E
I
X^
*
X3@
HCTR
}
HctrI
X^
*
X3@]
Set the horizontal location of first active
pixel in input
X^
.
Increment value
E
I
X^
–HCTR
}
HctrI
X^
*
X3@]
Increase the value by one pixel (shift the
image to the right).
Decrement value
E
I
X^
+HCTR
}
HctrI
X^
*
X3@]
Decrease the value by one pixel (shift
the image to the left).
View
E
I
X^
HCTR
} X3@]
Show the horizontal location of first
active pixel in input
X^
.
Vertical shift (available for endpoint input 1 only)
Specify a value
E
I
X^
*
X3@
VCTR
}
VctrI
X^
*
X3@]
Set the vertical location of first active
pixel in input
X^
.
Increment value
E
I
X^
+VCTR
}
VctrI
X^
*
X3@]
Increase the value by one line (shift up).
Decrement value
E
I
X^
–VCTR
}
VctrI
X^
*
X3@]
Decrease the value by one line (shift down).
View
E
I
X^
VCTR
} X3@]
Show the vertical location of first active
pixel in input
X^
.
Save and recall analog input presets (available for endpoint input 1 only)
NOTES:
• Analog input presets are available for analog (RGB, YUVp, YUVi, S-video, composite) video input signals on an XTP CP 4i VGA
universal analog input board only.
• Analog input presets save a set of analog variables, such as: horizontal and vertical shift, pixel phase, color and tint, brightness
and contrast, and input type.
Save an analog input preset
X^
*1*
X3#
, Spr
X^
*1*
X3#]
Command character is a comma.
Recall an analog input preset
X^
*1*
X3#
. Rpr
X^
*1*
X3#]
Command character is a period.
NOTE: X^ = Input number (for other than tie) 01 – 16 or 32 for an input
X2( = Input video source 0 = Auto (default) 2 = S-video 4 = YUV interlace 6 = YUV
1 = Video 3 = RGBcvS (SCART) 5 = RGB
X3) = Detected video format 0 = No signal detected 2 = S-video 4 = YUV interlace 6 = YUV
1 = Video 3 = RGBcvS (SCART) 5 = RGB
X3! = Picture adjustments 000 through 255 (128 = default)
X3@ = Shift 00000 through 65535
X3# = Analog input preset 1 through 8
X5% = Transmitter endpoint input 1-3 for the XTP T USW 103