Name: Fargo DTC400
Brand: Fargo
Rating: 5 (1 reviews)

To Next Page

To Previous Page

RESTRICTED USE ONLY Fargo Electronics, Inc.

DTC400 Card Printer/Encoder User Guide (Rev. 2.2)

Using the Diagnostics button under the Card tab _________________________________________ 6-9

Using the Clean Printer Option______________________________________________________ 6-10

Using the Test Print button_________________________________________________________ 6-12

Using the About button____________________________________________________________ 6-13

Using the Device Options tab (DTC400) ________________________________________________ 6-14

Reviewing the Device Options tab (DTC400) __________________________________________ 6-14

Adjusting the Ribbon Type option ___________________________________________________ 6-15

Selecting the Auto Ribbon Select option ______________________________________________ 6-16

Using the new Printer Driver (Rev. 2.1.5) _____________________________________________ 6-17

Changing the Color Profile Selection for the DTC400____________________________________ 6-17

Adjusting the Color Matching option_________________________________________________ 6-19

Adjusting for the Resin Dither ______________________________________________________ 6-20

Using the Print Both Sides option____________________________________________________ 6-21

Using the Split 1 Set of Ribbon Panels option __________________________________________ 6-22

Using the Print Back Side First option ________________________________________________ 6-23

Using the Print Back Side Only option________________________________________________ 6-24

Using the Rotate Front 180 Degrees or Rotate Back 180 Degrees options ____________________ 6-25

Using the Disable Printing option____________________________________________________ 6-26

Using the Image Color tab____________________________________________________________ 6-27

Using the Resin Heat (K) option (Front and Back) ______________________________________ 6-28

Using the Overlay Heat (O) option___________________________________________________ 6-29

Using the Color Matching option and Default button_____________________________________ 6-30

Using the Calibrate tab ______________________________________________________________ 6-31

Using the Image Position Controls___________________________________________________ 6-32

Using the Sensors button __________________________________________________________ 6-34

Using the Settings button __________________________________________________________ 6-35

Using the Magnetic Encoding tab ______________________________________________________ 6-36

Using the Magnetic Track Selection radio buttons_______________________________________ 6-37

Using the Magnetic Track Options radio buttons________________________________________ 6-39

Using the Bit Density radio buttons __________________________________________________ 6-40

Using the Character Size radio buttons________________________________________________ 6-41

Reviewing the Enable MLE Support checkbox _________________________________________ 6-42

Using the ASCII Offset radio buttons_________________________________________________ 6-43

Using the LRC Generation radio buttons ______________________________________________ 6-44

Using the Character Parity radio buttons ______________________________________________ 6-44

Using the Shift Data Left checkbox __________________________________________________ 6-45

Reviewing the ISO Track Locations__________________________________________________ 6-46

Sending the Track Information______________________________________________________ 6-47

Entering the Track Information _____________________________________________________ 6-47

Reviewing Tracks 1, 2 and 3 (in table format) __________________________________________ 6-48

Reviewing the Track Data Note _____________________________________________________ 6-48

Reviewing the ASCII Code and Character Table________________________________________ 6-49

Using the Overlay / Print Area tab _____________________________________________________ 6-50

Enabling the Frontside and Backside options___________________________________________ 6-51

Enabling the Frontside option (Overlay / Print Area)_____________________________________ 6-52

Enabling the Backside option (Overlay / Print Area) _____________________________________ 6-53

Using the Overlay / Print Area dropdown menu ________________________________________ 6-54

Using the Overlay / Print Area ______________________________________________________ 6-56

Using the Defined Area Option _____________________________________________________ 6-58

Using Security Options (Visual Security Solutions) (Frontside option only)___________________ 6-63

Selecting Orientation - Landscape under Card tab _______________________________________ 6-64

Selecting the Visual Security Solutions dropdown menu (A to D) __________________________ 6-65

Selecting Orientation - Portrait under Card tab _________________________________________ 6-66

Selecting the Visual Security Solutions dropdown menu (E to H)___________________________ 6-67

Selecting the VeriMark radio button (Frontside option only)_______________________________ 6-68

Selecting the HoloMark radio button (Frontside option only) ______________________________ 6-69

Fargo DTC400 User Manual

Table of Contents

Other manuals for Fargo DTC400

Questions and Answers:

Fargo DTC400 Specifications

Related product manuals

Brand	Fargo
Model	DTC400
Category	Printer
Language	English