Flintec EM100-C - Dimensions

To Next Page

To Previous Page

EM100-C User Manual

0084292

Page 12 of 81

3.2. Dimensions

External Dimensions (Top Side)

External Dimensions (Underside)

Main Page

Table of Contents2
EM100 Module7
Introduction7
Disclaimer8
Safety Instructions9
Specification10
Getting Started11
Labelling11
Dimensions12
Connections13
Load-Cell Connections14
Power Connection15
RS-232 Connection16
RS-485 Connection17
Canopen Connection18
USB Connection18
EM100 with Adaptor Board19
Driver Check20
Calibration21
Calibration Commands21
Preparing for Calibration21
Calibration Sequence22
Commands Overview23
Command Descriptions26
System Diagnostic Commands -FPN, FFV, IS, SR, RS26
FPN Get Device Identity26
FFV Get Firmware Version26
IS Get Device Status26
SR Software Reset27
RS Read Serial Number27
Calibration Commands - CE, CM'n', CI, MR, DS, DP, CZ, CG, ZT, FD, IZ, ZR, ZI, TM28
Tn, Zn, Az, Ag, Wt28
CE Read TAC Counter/Open Calibration Sequence28
CM 'N' Set Maximum Output Value28
CI Set Minimum Output Value29
MR Set Multi-Range/Multi-Interval29
DS Set Display Step Size29
DP Set Decimal Point Position30
Set Calibration Zero Point30
CG Set Calibration Gain (Span)30
ZT Enable/Disable Zero-Tracking31
FD Reset to Factory Default Settings31
IZ Correction of System Zero31
ZR Zero Range32
ZI Initial Zero Range32
TM Tare Mode32
TN Set/Clear Non-Volatile Tare33
ZN Set/Clear Non-Volatile Zero33
AZ Absolute Zero Point Calibration (Ecal)33
AG Absolute Gain Calibration (Ecal)34
WT Warm-Up Time34
Motion Detection Commands - NR, NT35
NR Set No-Motion Range35
NT Set No-Motion Time35
Filter Setting Commands - FM, FL, UR36
FM Filter Mode36
FL Filter Setting36
UR Update Rate & Averaging38
Taring & Zeroing Commands - SZ, RZ, ST, RT, SP, TMV, RMV39
SZ Set System Zero39
RZ Reset Zero39
ST Set Tare40
RT Reset Tare40
SP Set Preset Tare40
TMV Set Tare (MV/V)40
RMV Reset Tare (MV/V)41
Output Commands - GG, GN, GT, GS, GMV, GW, GA, GL, OF, GH, TH, GM, RM, GO42
Gv, Hw42
GG Get Gross Value42
GN Get Net Value42
GT Get Tare Value42
GS Get ADC Sample Value42
GMV Get MV/V Value42
GW Get Data String (Net, Gross & Status)43
GA Get Triggered Average Value44
GL Get Data String (Average, Gross & Status)44
OF Output Format of Data String44
GH Get Hold Value45
TH Trigger Hold Value45
GM Get Peak Value45
RM Reset Peak Value45
GO Get Peak-To-Peak Value45
GV Get Valley Value46
HW Hold Weight46
Auto-Transmit Commands - SG, SN, SX, SMV, SA, SL, SW47
SG Send Gross Value Continuously47
SN Send Net Value Continuously47
SX Send ADC Sample Value Continuously47
SMV Send MV/V Sample Value Continuously47
SA Send Triggered Average Value Continuously47
Send Data String Continuously (Average, Gross & Status)48
SW Send Data String Continuously (Net, Gross & Status)48
Commands for External I/O Control - IN, OM, IO49
IN Read Status of Logic Inputs49
OM Control of Logic Outputs by Host Application49
IO Read/Modify Status of Logic Outputs49
Set-Point Output Commands - S'n', H'n', A'n51
S'n' Set-Point Value51
H'n' Hysteresis & Switching Action for Set-Point51
A'n' Source Allocation for Set-Point52
Communication Setup Commands - AD, NA, NS, BR, DX, CL, OP, TD, CTR, STR, SBR53
AD Device Address - Serial Channel53
NA Network Address - Canopen53
NS Network Settings - Canopen53
BR Baud-Rate - Serial Channel54
DX Full-Duplex - Serial Channel54
CL Close Device Address 'N54
OP Open Device54
TD Transmission Delay55
CTR Set CAN Bus Termination Resistance55
STR Set RS-485 Termination Resistance55
SBR Set RS-485 Biasing Resistance55
Save Calibration & Setup Data Commands - CS, WP, SS56
CS Save Calibration Data56
WP Save Setup Parameters56
SS Save Set-Point Parameters56
Trigger Commands - SD, MT, TE, TR, TL57
SD Start Delay Time57
MT Measuring Time57
TE Trigger Edge57
TR Software Trigger58
TL Trigger Level58
Re-Trigger Commands - RW, TT, TS, DT, TW, TI, HT59
RW Re-Trigger Window59
TT Average Time for Re-Trigger Function59
TS Stop Value for Re-Trigger Function59
DT Short-Time Averaging Period60
TW Window for Automatic Taring60
TI Average Time for Automatic Taring60
HT Hold-Time for All Set-Points60
Canopen Interface62
General Interface Specification62
Pdos63
TPDO Frame (TPDO1, TPDO2 & TPDO3)65
TPDO Frame (TPDO4)65
Receive Pdos (RPDO1 & RPDO2)66
Sdos67
Communication Profile68
Object Dictionary68
Canopen Frames76
SDO CAN Frame76
Overall CAN Frame77
SDO Write78
NMT Master Message79
Heartbeat Message79
Emergency Message79

Flintec EM100-C - Dimensions

Table of Contents

Related product manuals