58 ADV100 • Quick installation guide - Specifications and connection
Step 1 - Electrical connections
Make the connections as described in paragraph 7.4.2.
Checks to be performed before powering the drive
• Check that the supply voltage is correct and that the input terminals on the drive (L1, L2 and L3) are connected
correctly.
• Check that the output terminals on the drive (U, V and W) are connected to the motor correctly.
• Check that all the drive control circuit terminals are connected correctly. Check that all control inputs are open.
Powering the drive
• After completing all the checks described above, power the drive and proceed to step 2.
Step 2 - Setting motor parameters
Set the rating data of the motor connected: rated voltage, rated frequency, rated current, rated speed, rated power,
power factor (cosφ).
10 Hp
Motor: 3 phase
720 rpm
Motor & Co.
Type: ABCDE
380 V
IP54
Made in ..............
19.0 A
IEC 34-1 / VDE 0530
Iso Kl F
Nr
.
12345-91
S1
50 Hz
Power factor
0.83
I nom
Rated voltage
Rated power
Rated speed (n )
N
The self-tuning procedure is described below using the data of an imaginary motor by way of example.
STARTUP WIZARD
Set motor data?
E=Yes Down=Next
E
SEQ
SEQ. 01 PAR: 2000
Rated voltage
400 V
Def: 400
E
SEQ
SEQ. 01 PAR: 2000
Rated voltage
000000400 v
Def: 400
▲
401 v
▼
399 v
E
SEQ
SEQ. 02 PAR: 2002
Rated current
11.8 A
Def: 11.8
E
SEQ
SEQ. 02 PAR: 2002
Rated current
00000011.8 A
Def: 11.8
▲
11.9 A
▼
11.7 A
E
SEQ
SEQ. 03 PAR: 2004
Rated speed
1450 r
p
m
Def: 1450
E
SEQ
SEQ. 03 PAR: 2004
Rated speed
0000001450 r
p
m
Def: 1450
▲
1451 rpm
▼
1449 rpm
E
SEQ
SEQ. 04 PAR: 2006
Rated frequency
50 Hz
Def: 50
E
SEQ
SEQ. 04 PAR: 2006
Rated frequency
000000050 Hz
Def: 50
▲
51 Hz
▼
49 Hz
E
SEQ
SEQ. 05 PAR: 2008
Pole pairs
2
Def: 2
E
SEQ
SEQ. 05 PAR: 2008
Pole pairs
2
Def: 2
▲
3
▼
1
E
SEQ
SEQ. 06 PAR: 2010
Rated power
5.50 kW
Def: 5.50
E
SEQ
SEQ. 06 PAR: 2010
Rated power
0000005.50 kW
Def: 5.50
▲
5.51 kW
▼
5.49 kW
E
SEQ
SEQ. 07 PAR: 2012
Rated power factor
0.83
Def: 0.83
E
SEQ
SEQ. 07 PAR: 2012
Rated power factor
0.83
Def: 0.83
▲
0.84
▼
0.82
E
Set the plate data of the motor connected, according to the procedures described on the previous pages.
Rated voltage [V]: the rated voltage of the motor indicated on the data plate.
Rated current [A]: motor rated current; approximately, the value should not be less than 0.3 times the rated current of the drive, output current class 1 @ 400 V
on the data plate of the drive.
To Next Page
Loading...
