GRAPHTEC LABELROBO LCX603 - Error Messages

7-8
Chapter 7 Troubleshooting
7.3 Error Messages
*When the following error messages occur, turn off the power, and turn the power on after the error has been solved.
LCD Display Cause Solution
'
'
'
'
E 0 1 : P r i n t e r j a m m i n g .
C h e c k t h e m e d i a
s t o c k e r a n d t h e
p r e s s r o l l e r .
Ribbon Wind-up
Jammed paper
Reset the media (or the ribbon).
'
'
'
'
E 0 2 : P r i n t e r j a m m i n g .
C h e c k t h e d a n c e r
r o l l e r 1 a n d t h e n
t u r n o f f t h e p o w e r .
Paper transfer abnormality
Dancer roller setting is lost
Jammed paper
Reset the media
Verify dancer roller 1.
'
'
'
'
E 0 3 : P r i n t e r j a m m i n g .
C h e c k t h e d a n c e r
r o l l e r 2 a n d t h e n
t u r n o f f t h e p o w e r .
Paper transfer abnormality
Dancer roller setting is lost
Jammed paper
Reset the media.
Verify dancer roller 2.
'
'
'
'
E 0 4 : P o s i t i o n e r r o r
T h e s l i d e r m o v e m e n t
w a s b l o c k e d .
T u r n o f f t h e p o w e r .
*
Abnormal shuttle stop
Cutter bade stops in progress
Jammed paper
Reset the media, turn on the power once again.
Verify the motor operating state.
'
'
'
'
E 0 5 : R M S s e n s o r e r r o r
C h e c k t h e p r i n t i n g
c o n d i t i o n f o r t h e
s t a r t i n g m a r k .
*
Start marks are not read. Start marks are not read.
Verify the start mark printing state.
Verify the ink ribbon and the media.
'
'
'
'
E 0 6 : R M S s e n s o r e r r o r
C h e c k t h e p r i n t i n g
c o n d i t i o n f o r R M S .
T u r n o f f t h e p o w e r .
*
Registrations are not read. Registration marks are not read.
Verify the registration mark printing state.
Verify the ink ribbon and the media.
'
'
'
'
E 0 7 : C r o s s c u t t e r
j a m m i n g . C h e c k t h e
c r o s s c u t t e r .
T u r n o f f t h e p o w e r .
*
Abnormal cross cut operation.
(Media cannot be cut.)
Seal case paper jam
Clean the cross cutter.
Verify the operating state of cross cut sensors F
and R.
Reset the media.
Tried to cut only the media and
backing sheet (or apply lamination)
Cut the backing sheet only.
'
'
'
'
E 0 8 : C r o s s c u t m a r k
C a n n o t r e a d t h e
c r o s s c u t m a r k .
*
Cross cut marks are not read.
Print problem, bowing, conveyance
slip.
Reset the media.
Verify the operating state of cross cut mark
sensors.
'
'
'
'
E 0 9 : P r i n t d a t a e r r o r
T h e u n k n o w n d a t a w a s
r e c e i v e d .
C h e c k t h e d a t a .
Data stops in progress
Unrecognizable data is received
Verify the DATA.
'
'
'
'
E 1 0 : H e a d t e m p e r a t u r e
L o w t e m p e r a t u r e o r
e r r o r m e a s u r e .
T u r n o f f t h e p o w e r .
Print head error Turn off the power.
If there are multiple occurrences, please contact
the distributor where you purchased the unit or
your nearest Graphtec vender.
'
'
'
'
E 9 0 : C u t t e r u n i t
c o m m u n i c a t i o n e r r o r .
T u r n o f f t h e p o w e r .
*
Communication error Turn off the power.
If there are multiple occurrences, please contact
the distributor where you purchased the unit or
your nearest Graphtec vender.
* When this error message occurs while performing copying, pressing the “NEXT” key will display the target number of
copies currently being printed. (This display will continue for as long as “NEXT” is being pressed, and will disappear
once the button is released.)