7-9
Chapter 7 Troubleshooting
7.4 Warning Messages
LCD Display Cause Solution
'
'
'
'
W 0 1 : N o m e d i a
L o a d t h e m e d i a .
( F E E D - k e y )
Media has not been set.
Media has finished.
There is no media. Please set media.
'
'
'
'
W 0 2 : N o r i b b o n
C o n f i r m r i b b o n f o r
h e a d 1 .
Media has not been set.
Media has finished.
Ribbon has broken.
Ribbon has jammed.
There is no ribbon for Head 1, or the ribbon has
broken. Replace the ribbon for Head 1.
'
'
'
'
W 0 2 : N o r i b b o n
C o n f i r m r i b b o n f o r
h e a d 2 .
Media has not been set.
Media has finished.
Ribbon has broken.
Ribbon has jammed.
There is no ribbon for Head 2, or the ribbon has
broken. Replace the ribbon for Head 2.
'
'
'
'
W 0 2 : N o r i b b o n
C o n f i r m r i b b o n f o r
h e a d 3 .
Media has not been set.
Media has finished.
Ribbon has broken.
Ribbon has jammed.
There is no ribbon for Head 3, or the ribbon has
broken. Replace the ribbon for Head 3.
'
'
'
'
W 0 3 : C o n f i r m !
R i b b o n l e v e r 3 i s
n o t s e t .
S e t r i b b o n l e v e r 3 !
Ribbon lever 3 is open.
Lever has opened during printing.
Ribbon lever 3 has released. Set ribbon lever 3
that is printing.
'
'
'
'
W 0 4 : L o a d i n g c h e c k
R i b b o n l e v e r i s s e t .
C a n n o t f e e d .
Y E S : E N T E R
Ribbon lever has not been released. Paper cannot be fed because the ribbon lever
has not been released Press the ENTER key.
(When feeding, release the ribbon lever.)
'
'
'
'
W 0 5 : C h e c k r i b b o n
l e v e r a n d p r i n t d a t a
L e v e r i s n o t s e t .
S e t r i b b o n l e v e r
There is no ribbon that corresponds
to the data (It is open).
There is no ribbon that corresponds to the data (It
is open).
Close the corresponding ribbon.
'
'
'
'
W 0 6 : H e a d t e m p e r a t u r e
H e a d t e m p e r a t u r e i s
h i g h . W a i t t o c o o l
d o w n t h e h e a d .
The head temperature is high
(shutdown to protect head)
Wait until the head temperature goes down.
'
'
'
'
W 0 7 : P r e s s r o l l e r s e t
P r e s s r o l l e r l e v e r
i s n o t s e t . S e t t h e
p r e s s r o l l e r l e v e r !
The press roller lever has not been
set.
The press roller lever has not been set. Set the
press roller.
'
'
'
'
W 0 8 : L o a d i n g c h e c k
P r e s s r o l l e r l e v e r
i s s e t t i n g . R e l e a s e
p r e s s r o l l e r l e v e r !
The press lever has been set. When media is supplied, the press lever is not
open. Open the press lever.
'
'
'
'
W 0 9 : N o l a m i n a t e
L o a d l a m i n a t e !
T h e n p r e s s E N T E R . O r
p r e s s F 4 t o c o n t i n u e
*
Unit menu = Laminate: ON
Laminate has not been set.
Laminate has finished.
There is no laminate. Set the laminate. (Or, turn
the unit off with the F4 key.
'
'
'
'
W 1 0 : L a m i n a t e i s i n s -
t a l l e d . R e m o v e i t !
T h e n p r e s s E N T E R . O r
p r e s s F 4 t o c o n t i n u e
Unit menu = Laminate: OFF
Laminate has been set.
The setting in the functional settings and the
laminate set state do not agree. Remove the
laminate or turn laminate ON in the functional
settings.
'
'
'
'
W 1 1 : L a m i n a t e w i n d e r
W i n d e r f u l l !
R e p l a c e t h e b o b b i n .
*
The take-up quantity is full. The laminate take-up is over capacity. Replace
the laminate winder bobbin.
'
'
'
'
W 1 2 : C u t t e r m e d i a
N o M e d i a !
L o a d t h e m e d i a t o
c u t t e r u n i t .
The media has not been set. The media has not been set in the cutter section.
Set the media.
To Next Page
Loading...