GRAPHTEC LABERLROBO DLC1000 - Index

I-1
INDEX
A
Acceleration ................................ 2-64
Accessories .................................. 1-2
AC line inlet .................................. 1-4
Adjusting the Blade Length .................. 2-2, 2-71
Adjustment for Half Cutting ...................... 2-75
Adjustment of Offset ........................... 2-75
Aligning the Push Rollers ...................... 2-39
Attaching a Tool .............................. 2-4
B
BAR CODE .................................. 4-19
Blade Application and Features .................. 2-3
Blade length ................................. 2-71
C
Can be stopped ............................... 2-76
CHANGE SETTINGS .......................... 4-9
COND/TEST ................................. 2-7
COND/TEST Key ......................... 2-6, 2-55
Control panel .............................. 1-3, 1-6
Control Panel ................................. 2-6
COPY ...................................... 4-6
Cross Cut ................................... 2-6
Cross cutter ................................. 2-29
Cross cutter unit .............................. 1-4
CUT CONDITION ........................ 2-56, 2-60
CUT CONDITION & TEST ................. 2-55, 2-56
CUT CONDITION & TEST screen ................ 2-7
Cutter Plunger Nomenclature .................... 2-2
Cutter unit ................................ 1-3, 1-6
Cutting area .................................. 2-11
Cutting mat .................................. 1-6
Cutting Test ................................. 2-72
CUTTING WIDTH ............................ 2-77
D
Dancer roller ....................... 1-2, 1-3, 1-4, 2-38
DATA Lamp .................................. 2-6
DHCP settings ................................ 5-4
DISTANCE ADJ. ............................. 4-25
Driver Software ............................... 3-2
E
Ejection roller ................................ 1-4
Ejection roller lever .................... 1-3, 2-20, 2-37
Emergency Stop Switch ..................... 1-4, 1-5
ENDING FEED ............................... 4-6
ENTER Key .................................. 2-6
Error Messages ............................... 6-5
ESC key ..................................... 2-76
ESC Key .................................... 2-6
F
Flange .................................. 1-2, 2-41
Flange A ............................ 1-2, 2-13, 2-32
Flange B ............................ 1-2, 2-13, 2-32
Force ...................................... 2-63
FRAME CUT ................................ 4-22
G
Gateway setting ............................... 5-7
Grit roller position guide ........................ 1-6
Grit rollers ................................... 1-6
I
I/F LAN ..................................... 5-3
IP address setting ............................. 5-5
L
Label Material Type ............................ 2-11
Label test 4 sheets ........................... 2-73
Laminate folder ............................... 1-4
Laminate holder .......................... 1-2, 2-41
Laminate material ............................. 2-11
Laminate winder bobbin ................. 1-2, 1-4, 2-45
LCD Display ................................ 2-56
LENGTH UNIT ............................... 4-27
M
MAC address display .......................... 5-8
Media Feed ........................... 2-6, 2-8, 2-31
Media position seal ........................... 2-29
Media sensors ................................ 1-6
Media Type .................................. 2-11
MENU ...................................... 2-7
MENU Key ................................... 2-6
MENU screen ................................ 2-7
N
Network interface ............................. 1-3
Network (LAN) Interface ........................ 5-2
Nomenclature ................................ 1-3
NUMBER OF POINTS ......................... 4-10
O
OFFSET FORCE ............................. 4-24
Optional Accessories .......................... A-4
Outline of Tangential Emulation
(TANGENTIAL MODE)
.........................
2-70
OVERCUT .................................. 2-68