Haas 96-8000 - Round Island

189
96-8000 Rev AC
May 2010
G & M Codes
Settings
X1. (12)
Y1. (13)
X2. (14) (Close Pocket Loop)
M99 (Return to Main Program)
%
Round Island
.
5
8
1, 12
2
X0, Y0
4, 10
3
5
5
Tool #1 isa.500
diameter end mill
G150 Pocket Milling (Round Island)
11
9
6, 7
Start Point
G150 Pocket Milling Program withaRound Island
5.0 x 5.0 x 0.500 DP. Square Pocket with Round Island
Main Program Subprogram
% %
O03010 O03020 (Subprogram for G150 in O03010)
T1 M06 (Tool is a 0.500” diameter endmill) G01 Y1. (1)
G90 G54 G00 X2. Y2. (XY Start Point) X6. (2)
S2500 M03 Y6. (3)
G43 H01 Z0.1 M08 X1. (4)
G01 Z0. F30. Y3.5 (5)
G150 P3020 X2. Y2. Z-0.5 Q0.5 R0.01 J0.3
K0.01 G41 D01 F10.
X2.5 (6)
G40 G01 X2. Y2. G02 I1. (7)
G00 Z1. M09 G02 X3.5 Y4.5 R1. (8)
G53 G49 Y0. Z0. G01 Y6. (9)
M30 X1. (10)
% Y1. (11)
X2. (12) (Close Pocket Loop)
M99 (Return to Main Program)
%
Absolute Subprogram Incremental Subprogram
% %
O01002 (G90 Subprogram for G150) O01002 (G91 Subprogram for G150
G90 G01 Y2.5 (1) G91 G01 Y0.5 (1)
X-2.5 (2) X-2.5 (2)
Y-2.5 (3) Y-5. (3)
X2.5 (4) X5. (4)
Y2.5 (5) Y5. (5)
X0. (6) X-2.5 (6)
M99 G90
% M99
%
Square Island
.
5
6
1, 14
2
7
8
10
X0, Y0
9
4
3
G150 Pocket Milling(Square Island)
Tool #1 isa.500
diameter end mill
5
5
13
11
12
Start Point
G150 Pocket Milling Program withaSquare Island
5.0 x 5.0 x 0.500 DP. Square Pocket with Square Island
Main Program Subprogram
% %
O02010 O02020 (Subprogram for G150 in O02010
T1 M06 (Tool is a 0.500” diameter endmill) G01 Y1. (1)
G90 G54 G00 X2. Y2. (XY Start Point) X6. (2)
S2500 M03 Y6. (3)
G43 H01 Z0.1 M08 X1. (4)
G01 Z0.01 F30. Y3.2 (5)
G150 P2020 X2. Y2. Z-0.5 Q0.5 R0.01 I0.3
K0.01 G41 D01 F10.
X2.75 (6)
G40 G01 X2.Y2. Y4.25 (7)
G00 Z1.0 M09 X4.25 (8)
G53 G49 Y0. Z0. Y2.75 (9)
M30 X2.75 (10)
Y3.8 (11)