Honeywell GX-Series User Manual

GX-Series Control Panel Installation and Setup Guide
6-39
Engineer 1
Option 51 – Parameters
This option allows the engineer to modify the system functions. Options can be selected using the A> or <B
keys or by entering the two digit parameter number and pressing the ent key. The selected options can then
be programmed by using the A> key to increase or the <B key to decrease the values assigned to the
parameter; pressing the ent key accepts the new value and returns to the previous menu level. Any
parameters that differ from this procedure are indicated in the following paragraphs. The parameters also
prompt the engineer on which keys to press.
For example, press:
• 1 then 6 parameter 16 = Soak Time selected;
• ent currently soak time is displayed along with the programmable range 07 (1–14) days;
• 08 value of the required soak time, the display shows the new value 08 (1–14) days;
• ent accept the programming and return to 16 = Soak Time displayed.
NOTE: Default settings must be changed before programming in Menu Option 55 – Soak.
Assigning Parameters to Groups
Several of the parameters allow separate values to be assigned to the groups on the system. If groups have
been enabled, the relevant parameters prompt for a group to be selected; when selected, the value is
assigned to the group parameter using the procedure outlined in the previous example.
The parameters that permit group selection are indicated in the following paragraphs.
Parameter Groups GX-Series Parameter Groups GX-Series
01 Bell Time
 
39 ATM Timeout not available 
02 Bell Delay
 
40 Not Used not available not available
03 Abort Time
 
41 Weekend Work not available

04 Exit Time
 
42 PIN Change not available

05 Entry Time
 
43 Not Used not available not available
06 System Reset
 
44 Early Open not available

07 Tamper Reset
 
45 High Security not available

08 No. Re-arms
 
46 Res. Select not available

09 Omit All
 
47 Set Confirm not available

10 Key '0' not available

48 Alarm Limits not available

11 Local Part 

49 Confirm Time not available

12 Banner not available

50 Not Used not available not available
13 PA Delay 

51 Not Used not available not available
14 KEY/SW Level not available

52 Not Used not available not available
15 System Text not available

53 Not Used not available not available
16 Soak Time not available

54 Keypad Access not available

17 Restart not available

55 Confirm not available

18 Stop Set not available

56 Force Restore not available

19 Part Alarm
 
57 Bell Extend not available

20 Power Delay
 
58 Power Alarm not available

21 Reset Mgr. not available

59 Part Tone not available

22 PA reset 

60 Not Used not available not available
23 Print Codes not available

61 Activity Mon not available

24 Exit Alarm 

62 Lockout not available

25 Global Copy not available

63 Banner alerts not available

26 Forced not available

64 Set Override not available

27 cct Debounce not available

65 Reset Levels not available

28 Online print not available

66 Min Pin Size not available

29 Online level not available

67 Level Format not available

30 Video
 
68 Line Fail not available

31 Delay Alarm
 
69 Alert Inds not available

32 Show Alarms not available

70 SWDC Set Dly not available

33 Secure Code not available

71 MF BL Enable not available

34 Comfort Time not available

72 Max Alm Cause not available

35 Fail To Set 

73 Guard Unset not available

36 Battery Size not available

74 Back-up Link not available

37 Standby Time not available

75 Back-up Timer not available

38 ATM Delay not available

Table 6-8. System Parameters

Honeywell GX-Series Specifications

General

Brand	Honeywell
Model	GX-Series
Category	Control Panel
Language	English