Honeywell UDC2300 User Manual

viii UDC2300 Controller Product Manual 12/00
Tables
Table 2-1 Condensed Specifications______________________________________________________4
Table 2-2 Preliminary Checks___________________________________________________________6
Table 2-3 Control Relay Contact Information ______________________________________________8
Table 2-4 Alarm Relay Contact Information _______________________________________________8
Table 2-5 Mounting Procedure_________________________________________________________10
Table 2-6 Permissible Wiring Bundling __________________________________________________12
Table 2-7 Universal Output Functionality and Restrictions___________________________________12
Table 4-1 Configuration Prompt Hierarchy _______________________________________________24
Table 4-2 Configuration Procedure _____________________________________________________25
Table 4-3 TIMER Group (Numeric Code 100) Function Prompts______________________________26
Table 4-4 TUNING Group (Numeric Code 200) Function Prompts ____________________________27
Table 4-5 SPRAMP Group (Numeric Code 300) Function Prompts ____________________________29
Table 4-6 ATUNE Group (Numeric Code 400) Function Prompts _____________________________31
Table 4-7 ALGOR Group (Numeric Code 500) Function Prompts _____________________________32
Table 4-8 INPUT1 Group (Numeric Code 600) Function Prompts _____________________________33
Table 4-9 INPUT2 Group (Numeric Code 700) Function Prompts _____________________________35
Table 4-10 CONTRL Group (Numeric Code 800) Function Prompts ___________________________36
Table 4-11 Options Group (Numeric Code 900) Function Prompts_____________________________38
Table 4-12 Communications Group (Numeric Code 1000) ___________________________________39
Table 4-13 ALARMS Group (Numeric Code 1100) Function Prompts__________________________41
Table 5-1 Procedure to Enter a Security Code _____________________________________________47
Table 5-2 Annunciators_______________________________________________________________49
Table 5-3 Lower Display Key Parameter Prompts __________________________________________50
Table 5-4 Error Messages_____________________________________________________________51
Table 6-1 Single Display Parameters ____________________________________________________55
Table 6-2 Procedure for Starting Up the Controller_________________________________________56
Table 6-3 Control Mode Definitions_____________________________________________________57
Table 6-4 Changing Control Modes (Dual Display Only) ____________________________________58
Table 6-5 Procedure for Changing the Local Setpoints ______________________________________58
Table 6-6 Procedure for Switching Between Setpoints ______________________________________59
Table 6-7 Procedure for Starting “TUNE” ________________________________________________61
Table 6-8 Procedure for Using TUNE at Start-up for Duplex Control___________________________62
Table 6-9 Procedure for Accessing Accutune Error Codes ___________________________________63
Table 6-10 Accutune Error Codes ______________________________________________________63
Table 6-11 Set Up Procedure __________________________________________________________65
Table 6-12 Procedure for Switching PID SETS from the Keyboard ____________________________65
Table 6-13 Procedure for Displaying Alarm Setpoints_______________________________________66
Table 6-14 Procedure for Displaying 3Pstep Motor Position__________________________________67
Table 6-15 Procedure for Setting a Failsafe Value__________________________________________68
Table 6-16 Procedure for Setting a Failsafe Mode__________________________________________69
Table 7-1 Running A Setpoint Ramp ____________________________________________________73
Table 7-2 Program Contents ___________________________________________________________75
Table 7-3 Run/Monitor Functions ______________________________________________________80
Table 8-1 Voltage and Resistance Equivalents for Input 1 Range Values ________________________84
Table 8-2 Equipment Needed __________________________________________________________86
Table 8-3 Set Up Wiring Procedure for Thermocouple Inputs Using an Ice Bath _________________87
Table 8-4 Set Up Wiring Procedure for Thermocouple Inputs using Thermocouple Source _________87

Honeywell UDC2300 Specifications

General

Brand	Honeywell
Model	UDC2300
Category	Controller
Language	English