EasyManuals Logo

Huawei S1720 Series Configuration Guide

Huawei S1720 Series
664 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #244 background imageLoading...
Page #244 background image
Configuration Roadmap
The configuration roadmap is as follows:
1. Configure IPv6 addresses for interfaces.
2. Enable the basic OSPFv3 functions on each Switch.
3. Configure a virtual link between Switch B and Switch C to connect the non-backbone areas
to the backbone area.
Data Preparation
To complete the configuration, you need the following data:
l Router ID (1.1.1.1) of Switch A and area (Area 2) where Switch A is located
l Router ID (2.2.2.2) of Switch B and areas (Area 1 and Area 2) where Switch B is located
l Router ID (3.3.3.3) of Switch C and areas (Area 1 and Area 0) where Switch C is located
l Router ID (4.4.4.4) of Switch D and area (Area 0) where Switch D is located
Procedure
Step 1 Add interfaces to VLANs.
<Quidway> system-view
[Quidway] sysname SwitchA
[SwitchA] vlan 10
[SwitchA-vlan10] quit
[SwitchA] interface XGigabitEthernet 0/0/1
[SwitchA-XGigabitEthernet0/0/1] port hybrid pvid vlan 10
[SwitchA-XGigabitEthernet0/0/1] port hybrid untagged vlan 10
[SwitchA-XGigabitEthernet0/0/1] quit
The configurations of Switch B, Switch C, Switch D are similar to the configuration of Switch
A and are not mentioned here.
Step 2 Assign IPv6 addresses to the VLANIF interfaces.
[SwitchA] ipv6
[SwitchA] interface vlanif 10
[SwitchA-Vlanif10] ipv6 enable
[SwitchA-Vlanif10] ipv6 address 1001::2/64
[SwitchA-Vlanif10] quit
The configurations of Switch B, Switch C, Switch D are similar to the configuration of Switch
A and are not mentioned here.
Step 3 Configure the basic OSPFv3 functions.
# On Switch A, enable OSPFv3 and set the router ID to 1.1.1.1.
[Switch A] ospfv3
[Switch A-ospfv3-1] router-id 1.1.1.1
[Switch A-ospfv3-1] quit
[Switch A] interface Vlanif 10
[Switch A-Vlanif10] ospfv3 1 area 2
[Switch A-Vlanif10] quit
# On Switch B, enable OSPFv3 and set the router ID to 2.2.2.2.
[Switch B] ospfv3
[Switch B-ospfv3-1] router-id 2.2.2.2
[Switch B-ospfv3-1] quit
[Switch B] interface vlanif 10
S6700 Series Ethernet Switches
Configuration Guide - IP Routing 5 OSPFv3 Configuration
Issue 01 (2012-03-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
225

Table of Contents

Other manuals for Huawei S1720 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Huawei S1720 Series and is the answer not in the manual?

Huawei S1720 Series Specifications

General IconGeneral
Operating Humidity5% to 95% (non-condensing)
Uplink Ports4 x GE combo ports
VLANs4094
Power SupplyAC 100-240V, 50/60Hz
Layer 2 FeaturesVLAN
Layer 3 FeaturesStatic routing
ManagementSNMP
Operating Temperature0°C to 45°C
Storage Temperature-40°C to +70°C
Dimensions (W x D x H)442 mm x 220 mm x 43.6 mm

Related product manuals