To Next Page

To Previous Page

SURGesag Subsystem

Query syntax

SURGesag:PHASe:ENABle?

Returns

<NRf+>

Example

SURGesag:PHASe:ENABle ABC

SURGesag:ANGLe:ENABle <SYNC|SPEC>

This command is used to set and query the synchronization method of dropping

between three phases, SYNC means synchronous dropping, SPEC means

dropping at the respective specified phase. Only available in three-phase mode.

Syntax

SURGesag:ANGLe:ENABle < SYNC|SPEC >

Argument

<SYNC|SPEC>

Query syntax

SURGesag:ANGLe:ENABle?

Returns

<NRf+>

Example

SURGesag:ANGLe:ENABle SYNC

SURGesag:STATe?

This command is used to query the running status of the surge/trap wave.

Syntax

SURGesag:STATe?

Example

SURGesag:STATe? //Query the running status of the surge/trap wave.

default chapter3
- Limitation of Warranty3
- Safety Symbols3
- Warranty3
- Environmental Conditions4
- Regulatory Markings5
- Compliance Information6
- Table of Contents7
Chapter1 SCPI Introduction13
- 1.1 Overview13
- 1.2 Command Type of SCPI13
- 1.3 Message Type of SCPI15
- 1.4 Response Data Type17
- 1.5 Command Format17
- 1.6 Data Type19
- 1.7 Remote Interface Connection20
Chapter2 SCPI Status Register22
Chapter3 System Commands25
- System:preset29
- System:posetup <CPD29
- System:clear30
Chapter4 Source Commands40
- [Source:]Function <CPD1>[,CPD2]40
- [Source:]Function:mode <CPD40
- [Source:]Current:protection:rms <Nrf+> [,CH1|CH2|CH3]41
- [Source:]Current:protection:delay <Nrf+> [,CH1|CH2|CH3]41
- [Source:]Current:protection:delay? [Ch1|Ch2|Ch3],[Maximum|Minimum|Default]42
- [Source:]Current:protection:mode <CPD> [,CH1|CH2|CH3]42
- [Source:]Current:protection:peak <Nrf+> [,CH1|CH2|CH3]43
- [Source:]Current:protection:peak? [Ch1|Ch2|Ch3],[Maximum|Minimum|Default]43
- [Source:]Current:protection:peak:delay<Nrf+> [,CH1|CH2|CH3]44
- [Source:]Current:protection:peak:delay? [Ch1|Ch2|Ch3],[Maximum|Minimum|Default]44
- [Source:]Current:limit:high <Nrf+> [,CH1|CH2|CH3]45
- [Source:]Current:limit:low <Nrf+> [,CH1|CH2|CH3]45
- [Source:]Current[:Level][:Immediate][:Amplitude][:Ac] <Nrf+>[,Nrf+][,Nrf+]46
- [Source:]Current[:Level][:Immediate][:Amplitude]:DC <Nrf+>,[Nrf+],[Nrf+]46
- [Source:]Voltage[:Level][:Immediate][:Amplitude][:Ac] <Nrf+>[,Nrf+][,Nrf+]47
- [Source:]Voltage:limit:high <Nrf+> [,CH1|CH2|CH3]47
- [Source:]Voltage:limit:low <Nrf+> [,CH1|CH2|CH3]48
- [Source:]Pvoltage[:Level][:Immediate][:Amplitude][:Ac] <Phase>,<Nrf48
- [Source:]Voltage[:Level][:Immediate][:Amplitude]:DC <Nrf+>,[Nrf+],[Nrf+]49
- [Source:]Pvoltage[:Level][:Immediate][:Amplitude]:DC <Phase>,<Nrf49
- [Source:]Voltage:slope[:Ac][:Immediate] <Nrf+>,[Nrf+],[Nrf+]50
- [Source:]Pvoltage:slope[:Immediate][:Ac] <Phase>,<Nrf50
- [Source:]Voltage:slope[:Immediate]:DC <Nrf+>,[Nrf+],[Nrf+]50
- [Source:]Pvoltage:slope[:Immediate]:DC <Phase>,<Nrf51
- [Source:]Frequency[:Immediate] <Nrf+>[,Nrf+][,Nrf+]51
- [Source:]Pfrequency[:Immediate] <Phase>,<Nrf52
- [Source:]Frequency:slope[:Immediate] <Nrf+>[,Nrf+][,Nrf+]52
- [Source:]Pfrequency:slope[:Immediate] <Phase>,<Nrf53
- [Source:]Power:limit:high <Nrf+> [,CH1|CH2|CH3]53
- [Source:]Power:limit:low <Nrf+> [,CH1|CH2|CH3]53
- [Source:] Power:limit:delay <Nrf+> [,CH1|CH2|CH3]54
- [Source:]Angle:start[:Immediate] <Nrf54
- [Source:]Angle:stop[:Immediate] <Nrf55
- [Source:]Angle:difference[:Immediate] <Type>,<Nrf55
- [Source:]Wave[:Immediate] <Wave>,[Wave],[Wave]56
- [Source:]Pwave[:Immediate] <Phase>,<Wave56
- [Source:]Dimming[:State] <CPD>[,CH1|CH2|CH3]57
- [Source:]Dimming:edge <CPD>[,CH1|CH2|CH3]57
- [Source:]Dimming:phase <Nrf>[,Ch1|Ch2|Ch3]57
- [Source:]Extern:program[:State] <CPD58
- [Source:]Extern:program:mode <CPD58
- [Source:]Configure:harmonic:thd:formula <CPD58
- [Source:]Configure:harmonic:table:type <CPD59
- [Source:]Configure:harmonic:table:select <CPD59
Chapter5 Output Commands60
- Output[:State] <CPD60
- Output:protection:clear60
- Output:protection:wdog[:State] <CPD60
- Output:protection:wdog:delay <Nrf61
- Output:impedance[:State] <CPD>[,A|B|C|CH1|CH2|CH3]61
- Output:impedance:resistance:level <Nrf+>[,A|B|C|Ch1|Ch2|Ch3]62
- Output:impedance:inductance:level <Nrf>[,A|B|C|Ch1|Ch2|Ch3]62
- Output:off:mode <CPD63
- Output:on:phase:mode <CPD63
- Output:on:phase:level <Nrf63
- Output:off:phase:mode <CPD64
- Output:off:phase:level <Nrf64
- Output:balance[:State] <CPD65
Chapter6 Sense Commands66
- Sense[:Remote][:State] <CPD66
- Sense:filter[:State] <CPD66
- Sense:filter:level <CPD67
- Sense:loop:speed <CPD67
- Sense:external:frequency <CPD> [CH1, CH2, CH3]67
- Sense:external:frequency:offset:high <Nrf>,[Ch1, CH2, CH3]68
- Sense:external:frequency:offset:low <Nrf>,[Ch1, CH2, CH3]68
- Sense:external:frequency:phase <Nrf>,[Ch1, CH2, CH3]69
- Sense:external:frequency:exception <CPD>,[CH1, CH2, CH3]70
Chapter7 Fetch & Measure Commands71
- Fetch[:Scalar]:Current[:Ac]71
- Measure[:Scalar]:Current[:Ac]71
- Fetch[:Scalar]:Current:DC71
- Measure[:Scalar]:Current:DC71
- Fetch[:Scalar]:Current:amplitude:maximum:positive72
- Measure[:Scalar]:Current:amplitude:maximum:positive72
- Fetch[:Scalar]:Current:amplitude:maximum:negative72
- Measure[:Scalar]:Current:amplitude:maximum:negative72
- Fetch[:Scalar]:Current:amplitude:maximum73
- Measure[:Scalar]:Current:amplitude:maximum73
- Fetch[:Scalar]:Current:cfactor73
- Measure [:Scalar]:Current:cfactor73
- Fetch[:Scalar]:Frequency74
- Measure[:Scalar]:Frequency74
- Fetch[:Scalar]:Power[:Real]74
- Measure[:Scalar]:Power[:Real]74
- Fetch[:Scalar]:Power:apparent74
- Measure[:Scalar]:Power:apparent74
- Fetch[:Scalar]:Power:reactive75
- Measure[:Scalar]:Power:reactive75
- Fetch[:Scalar]:Power:pfactor75
- Measure[:Scalar]:Power:pfactor75
- Fetch[:Scalar]:Voltage[:Ac]76
- Measure[:Scalar]:Voltage[:Ac]76
- Fetch[:Scalar]:Voltage:DC76
- Measure[:Scalar]:Voltage:DC76
- Fetch[:Scalar]:Voltage:amplitude:maximum77
- Measure[:Scalar]:Voltage:amplitude:maximum77
- Fetch[:Scalar]:Voltage:amplitude:maximum:positive77
- Measure[:Scalar]:Voltage:amplitude:maximum:positive77
- Fetch[:Scalar]:Voltage:amplitude:maximum:negative78
- Measure[:Scalar]:Voltage:amplitude:maximum:negative78
- Fetch[:Scalar]78
- Measure[:Scalar]78
- Fetch[:Scalar]:Power[:Real]:Total79
- Measure[:Scalar]:Power[:Real]:Total79
- Fetch[:Scalar]:Power:apparent:total79
- Measure[:Scalar]:Power:apparent:total79
- Fetch[:Scalar]:Power:reactive:total80
- Measure[:Scalar]:Power:reactive:total80
- Fetch[:Scalar]:Ltlvoltage[:Ac]80
- Measure[:Scalar]:Ltlvoltage[:Ac]80
- Fetch[:Scalar]:Voltage:harmonic[:Amplitude]? <[A|B|C|CH1|CH2|CH3]>,<NR180
- Measure[:Scalar]:Voltage:harmonic[:Amplitude]? <[A|B|C|CH1|CH2|CH3]>,<NR180
- Fetch[:Scalar]:Current:harmonic[:Amplitude]? <[A|B|C|CH1|CH2|CH3]>,<NR181
- Measure[:Scalar]:Current:harmonic[:Amplitude]? <[A|B|C|CH1|CH2|CH3]>,<NR181
- Fetch[:Scalar]:Voltage:harmonic:distort? <[A|B|C|CH1|CH2|CH3]>,<NR181
- Measure[:Scalar]:Voltage:harmonic:distort? <[A|B|C|CH1|CH2|CH3]>,<NR181
- Fetch[:Scalar]:Current:harmonic:distort? <[A|B|C|CH1|CH2|CH3]>,<NR182
- Measure[:Scalar]:Current:harmonic:distort? <[A|B|C|CH1|CH2|CH3]>,<NR182
- Fetch[:Scalar]:Voltage:harmonic:phase? <[A|B|C|CH1|CH2|CH3]>,<NR182
- Measure[:Scalar]:Voltage:harmonic:phase? <[A|B|C|CH1|CH2|CH3]>,<NR182
- Fetch[:Scalar]:Current:harmonic:phase? <[A|B|C|CH1|CH2|CH3]>,<NR183
- Measure[:Scalar]:Current:harmonic:phase? <[A|B|C|CH1|CH2|CH3]>,<NR183
- Fetch[:Scalar]:Voltage:harmonic:thd? <[A|B|C|CH1|CH2|CH3]83
- Measure[:Scalar]:Voltage:harmonic:thd? <[A|B|C|CH1|CH2|CH3]83
- Fetch[:Scalar]:Current:harmonic:thd? <[A|B|C|CH1|CH2|CH3]84
- Measure[:Scalar]:Current:harmonic:thd? <[A|B|C|CH1|CH2|CH3]84
- Fetch[:Scalar]:Array:voltage:harmonic[:Amplitude]? <[A|B|C|CH1|CH2|CH3]>,<NR184
- Measure[:Scalar]:Array:voltage:harmonic[:Amplitude]? <[A|B|C|CH1|CH2|CH3]>,<NR184
- Fetch[:Scalar]:Array:current:harmonic[:Amplitude]? <[A|B|C|CH1|CH2|CH3]>,<NR185
- Measure[:Scalar]:Array:current:harmonic[:Amplitude]? <[A|B|C|CH1|CH2|CH3]>,<NR185
- Fetch[:Scalar]:Array:voltage:harmonic:phase? <[A|B|C|CH1|CH2|CH3]>,<NR185
- Measure[:Scalar]:Array:voltage:harmonic:phase? <[A|B|C|CH1|CH2|CH3]>,<NR185
- Fetch[:Scalar]:Array:current:harmonic:phase? <[A|B|C|CH1|CH2|CH3]>,<NR186
- Measure[:Scalar]:Array:current:harmonic:phase? <[A|B|C|CH1|CH2|CH3]>,<NR186
- Fetch[:Scalar]:Array:voltage:harmonic:distort? <[A|B|C|CH1|CH2|CH3]>,<NR186
- Measure[:Scalar]:Array:voltage:harmonic:distort? <[A|B|C|CH1|CH2|CH3]>,<NR186
- Fetch[:Scalar]:Array:current:harmonic:distort? <[A|B|C|CH1|CH2|CH3]>,<NR187
- Measure[:Scalar]:Array:current:harmonic:distort? <[A|B|C|CH1|CH2|CH3]>,<NR187
- Vetcor:oeder <NR187
- Vetcor:data88
- Vetcor:type <CPD88
Chapter8 Abort Subsystem89
- Abort:acquire89
- Abort:list89
- Abort:sweep89
- Abort:surgesag89
Chapter9 Initiate Subsystem90
- Initiate[:Immediate]:Acquire90
- Initiate[:Immediate]:List90
- Initiate[:Immediate]:Sweep90
- Initiate[:Immediate]:Surgesag90
Chapter10 Parallel Subsystem91
- Parallel:role <Role91
- Parallel:number <Number91
- Parallel:node:number92
Chapter11 Trigger Subsystem93
- Trigger:list:source <Source93
- Trigger:sweep:source <CPD93
- Trigger:surgesag:source <CPD94
- Trigger:scope:source <CPD94
- Trigger:scope:mode <CPD94
- Trigger:scope:slope <CPD195
- Trigger:force95
Chapter12 ARB Subsystem96
- [Arb:]List:state96
- [Arb:]List:repeat <NR196
- [Arb:]List:terminate <CPD96
- [Arb:]List:run97
- [Arb:]List:stop97
- [Arb:]List:runtime:state97
- [ARB:]LIST:RCL <String98
- [Arb:]List:step:count <NR198
- [Arb:]List:clear98
- [ARB:]LIST:STEP <Nr1>,<String99
- [ARB:]LIST:STEP:ITEM <Nr1>,<Nr2>,<Nrf100
- [ARB:]LIST:STEP:ITEM? <Nr1>,<Item102
- [Arb:]List:name102
- [Arb:]List:save <Filename102
- [Arb:]List:configure103
- [Arb:]List:initiate103
- [Arb:]List:abort103
- [Arb:]List:create103
- [Arb:]List:file:number103
- [ARB:]LIST:FILE:NAME? <Index104
- [Arb:]List:file:delete <Filename104
Chapter13 Configurate IO Subsystem105
- [Configurable:]Io:select <NR1105
- [Configurable:]Io:reverse <NR1>,<CPD105
- [Configurable:]Io:type <NR1>,<CPD106
- [Configurable:]Io:trigout:source <CPD1>,<CPD2106
- [Configurable:]Io:state <NR1>,<CPD107
Chapter14 Sweep Subsystem108
- Sweep:voltage:start <Nrf+>[,<Nrf+>,<Nrf+>]108
- Sweep:voltage:stop <Nrf+>[,<Nrf+>,<Nrf+>]108
- Sweep:voltage:step <Nrf+>[,<Nrf+>,<Nrf+>]109
- Sweep:freq:start <Nrf+>[,<Nrf+>,<Nrf+>]110
- Sweep:freq:stop <Nrf+>[,<Nrf+>,<Nrf+>]110
- Sweep:freq:step <Nrf+>[,<Nrf+>,<Nrf+>]111
- Sweep:time:step <Nrf+>[,<Nrf+>,<Nrf+>]111
- Sweep:mode <Mode112
- Sweep:priority<Priority113
- Sweep:waveform <Type113
- Sweep:finish <Mode114
- Sweep:trig:source <Mode114
- Sweep:step:repeat <NR1115
- Sweep:state115
Chapter15 Surgesag Subsystem116
- Surgesag:mode <Mode116
- Surgesag:phase:start <Nrf116
- Surgesag:phase:width <Nrf117
- Surgesag:action <Action117
- Surgesag:symmetry <Bool118
- Surgesag:repeat:count <NR1119
- Surgesag:period:count <NR1119
- Surgesag:value:select <Mode120
- Surgesag:value:percent <Nrf120
- Surgesag:value <Nrf121
- Surgesag:phase:enable <A|B|C|AB|AC|BC|ABC121
- Surgesag:angle:enable <SYNC|SPEC122
- Surgesag:state122
Chapter16 Scope Subsystem123
- Scope:auto123
- Scope:run123
- Scope:single123
- Scope:stop123
- Scope:timebase:scale <Nrf123
- Scope:voltage:scale <Nrf124
- Scope:current:scale <Nrf124
- Scope:timebase:delay <Nrf125
- Scope:trigger:level <Nrf125
- Scope:trigger:slope <CPD126
- Scope:trigger:mode <CPD126
- Scope:line:selection <NR1>,<BOOL126
- Scope:status127
- Scope:rstate127
- Scope:waveform:data127
Chapter17 Status Commands129
- Status:questionable[:Event]129
- Status:questionable:condition129
- Status:questionable:enable <NR1130
- Status:questionable:ntransition <NR1130
- Status:questionable:ptransition131
- Status:operation[:Event]131
- Status:operation:condition132
- Status:operation:enable <NR1132
- Status:operation:ntransition<Nr1133
- Status:operation:ptransition134
- Status:preset134
Chapter18 Waveform Subsystem135
- Waveform[:Immediate] <Waveform>,[Waveform],[Waveform]135
- Pwaveform[:Immediate] <Phase/Chan>,<Waveform135
- Waveform:edit:parameter <Phase/Chan>,<Percent1136
- Waveform:edit:thd:clear136
- Waveform:edit:thd:import <Filename137
- Waveform:edit:thd:formula <Formula137
- Waveform:edit:thd:data <Order>,<String138
- Waveform:edit:thd:save:local <Filename138
- Waveform:edit:thd:save:udisk <Filename138
- Waveform:edit:userdefine:clear139
- Waveform:edit:userdefine:import <Filename139
- Waveform:edit:userdefine:mode <Symmtery139
- Waveform:edit:userdefine:data <Index>,<Normalization140
- Waveform:edit:userdefine:save:local <Filename140
- Waveform:edit:userdefine:save:udisk <Filename141
- Waveform:edit:userdefine:extend141
- Waveform:edit:userdefine:extend:data <Index>,<Normalization141
Chapter19 Island Subsystem142
- Island:run:state142
- Island:time142
- Island:key1[:State] <CPD142
- Island:key2:State] <CPD143
- Island:resistance:level <Nrf+>[,A|B|C]143
- Island:inducatance:level <Nrf+>[,A|B|C]144
- Island:phase:level <Nrf+>[,A|B|C]144
- Island:cap:level <Nrf+>[,A|B|C]144
- Island:power:level <Nrf+>[,A|B|C]145
- Island:ql:level <Nrf+>[,A|B|C]145
- Island:qc:level <Nrf+>[,A|B|C]146
- Island:mode <CPD>[,CH1|CH2|CH3]146
- Island:inhibit[:State] <CPD147
- Island:voltage:control[:State] <CPD>[,CH1|CH2|CH3]147
- Island:voltage:control:level <Nrf+>[,A|B|C|Ch1|Ch2|Ch3]148
- Island:current:control[:State] <CPD>[,CH1|CH2|CH3]148
- Island:current:control:level <Nrf+>[,A|B|C|Ch1|Ch2|Ch3]148
- Island:power:control[:State] <CPD>[,CH1|CH2|CH3]149
- Island:power:control:level <Nrf+>[,A|B|C|Ch1|Ch2|Ch3]149
Chapter20 IEEE-488 Common Commands151
- Cls151
- Ese151
- Ese152
- Esr152
- Idn152
- Opc153
- Rst153
- Sre <Nr1153
- Stb154
- Psc154
- Sav155
- Rcl155

Brand	ITech
Model	IT7900 Series
Category	Power Supply
Language	English

ITech IT7900 Series Programming Guide

Table of Contents

Other manuals for ITech IT7900 Series

Questions and Answers:

ITech IT7900 Series Specifications

Related product manuals