EasyManuals Logo

Juniper SRX100 Hardware Guide

Juniper SRX100
154 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #145 background imageLoading...
Page #145 background image
To pack the services gateway for shipment:
1. Retrieve the shipping carton and packing materials in which the device was
originally shipped. If you do not have these materials, contact your Juniper
Networks representative about approved packaging materials.
2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and
connect the strap to the ESD point on the chassis or to an outside ESD point if
the device is disconnected from earth ground.
3. On the console or other management device connected to the services gateway,
enter CLI operational mode and issue the following command to shut down the
services gateway software:
user@host> request system power-off
Wait until a message appears on the console confirming that the operating system
has halted.
4. Shut down power to the device by pressing the Power button on the front panel
of the device.
5. Disconnect power from the device.
6. Remove the cables that connect to all external devices.
7. Remove all field-replaceable units (FRUs) from the device.
8. If the device is installed on a wall or rack, have one person support the weight
of the device while another person unscrews and removes the mounting screws.
9. Place the device in the shipping carton.
10. Cover the device with an ESD bag, and place the packing foam on top of and
around the device.
11. Replace the accessory box on top of the packing foam.
12. Securely tape the box closed.
13. Write the Return Materials Authorization (RMA) number on the exterior of the
box to ensure proper tracking.
Packing the Components for Shipment
Follow these guidelines for packing and shipping individual components of the
services gateway:
When you return a component, make sure that it is adequately protected with
packing materials and packed so that the pieces are prevented from moving
around inside the carton.
Use the original shipping materials if they are available.
Write the Return Materials Authorization (RMA) number on the exterior of the
box to ensure proper tracking.
CAUTION: Do not stack any of the services gateway components during packing.
Packing the SRX100 Services Gateway and Components for Shipment 127
Appendix D: Contacting Customer Support and Returning the SRX100 Services Gateway Hardware

Table of Contents

Other manuals for Juniper SRX100

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Juniper SRX100 and is the answer not in the manual?

Juniper SRX100 Specifications

General IconGeneral
Routing protocolsBGP, IS-IS, MPLS, OSPF
Switching protocolsVLAN 802.1Q, 802.3ad/LACP, STP
Supported network protocolsIPv4, IPv6, CLNS
Firewall securityYes
Security algorithms3DES, DES
Authentication methodRADIUS, RSA SecureID, LDAP
VPN supportIPsec VPN
Data transfer rate0.1 Gbit/s
Input voltage100 - 240 V
Input frequency50/60 Hz
Heat dissipation35 BTU/h
Power requirements100-240, 50/60
Power over Ethernet (PoE)No
Power consumption (typical)30 W
SafetyUL 60950-1, CSA 60950-1, AS / NZS 60950-1, AS / NZS 60950-1, CB Scheme, EN 60950-1
CertificationFCC Class B ICES class B AS / NZS CISPR22 Class B AS / NZS CISPR22 Class B VCCI Class B EN 55022 Class B, EN 300386
Mounting typeRack mounting
Internal memory1024 MB
Storage temperature (T-T)-20 - 70 °C
Operating temperature (T-T)0 - 40 °C
Weight and Dimensions IconWeight and Dimensions
Weight1100 g
Dimensions (WxDxH)216 x 147 x 36 mm

Related product manuals