Lenze 8400 motec User Manual

8400 motec | Software Manual
Index
370 L Firmware ≤ 02.00 - DMS 2.1 EN - 03/2011
xx.0145.00003 217
xx.0145.00004 217
xx.0145.00005 218
xx.0145.00006 218
xx.0145.00007 218
xx.0145.00008 218
xx.0145.00009 218
xx.0145.00010 219
xx.0400.00105 219
xx.0980.00000 219
xx.0981.00000 219
Error number (C00168) 259
Error subject area 205
Error type 204
Exporting logbook entries 198
F
Feedback to Lenze 374
FI brake 114
Fieldbus interface 220
Filter time - oscill. damping (C00235) 264
Firmware compile date (C00201) 261
Firmware product type (C00200) 261
Firmware version (C00099) 247
Firmware version (C00100) 247
Fixed setpoint x (L_NSet_1 n-Fix) (C00039) 242
Flying restart function 100
Activation (C00990) 293
Current (C00994) 293
Process (C00991) 293
Start frequency (C00992) 293
FreqInxx
Gain (C02843)
304
Offset (C02842) 304
FreqInxx_nOut_a (C00446) 269
FreqInxx_nOut_v (C00445) 268
Frequency limitation (C00910) 290
Function blocks 313
Function library 313
G
General purpose functions 153
H
Heat capacity brake resistor (C00131) 251
Heatsink temperature (C00061) 243
Holding brake
Activation time (C02593)
302
Operating mode (C02580) 300
Setting (C02582) 301
Speed thresholds (C02581) 300
Status (C02607) 303
Time system (C02589) 302
Holding brake control 177
I
ID1
Motor data identification error (error message)
212
Imax controller 70
Imax in generator mode (C00023) 240
Imax in motor mode (C00022) 239
Internal bus counter (C295) 265
Internal wiring
Control mode "Network"
166
Control mode "Terminals 0" 165
Inverter motor brake 114
nAdd (C00987) 292
K
Keypad
(C00463)
269
Default parameter (C00466) 269
Default welcome screen (C00467) 269
STOP key function (C00469) 269
Keypad/PC
Setpoint control (C462)
269
Speed setpoint (C729) 284
L
L_Compare 332
L_Compare_1 332
Fct. (C00680) 282
Hysteresis (C00681) 282
Window (C00682) 282
L_Counter 337
L_Counter_1 337
Comparison (C01101) 295
Function (C01100) 295
L_DigitalDelay 339
L_DigitalDelay_1 339
Delay (C00720) 283
L_DigitalDelay_2 342
Delay (C00721) 284
L_DigitalLogic 343
L_DigitalLogic_1 343
Function (C00820) 286
Truth table (C00821) 286
L_GP_Compare1 332
L_GP_Counter1 337
L_GP_DigitalDelay1 339
L_GP_DigitalDelay2 342
L_GP_DigitalLogic1 343
L_MPot 314
L_MPot_1 314
Acceleration time (C00802) 284
Deceleration time (C00803) 285
Inactive fct. (C00804) 285
Init fct. (C00805) 285
Lower limit (C00801) 284
Upper limit (C00800) 284

Lenze 8400 motec Specifications

General

Input Voltage	3-phase 380V to 480V AC
Control Mode	Vector control
Communication	CANopen, PROFIBUS, Ethernet
Protection Features	Overcurrent, overvoltage, undervoltage, short-circuit, overtemperature
Relative Humidity	≤ 95 %, no condensation
Altitude	Up to 1000m above sea level
Storage Temperature	-20°C to 65°C