Lenze 8400 motec User Manual

8400 motec | Software Manual
Index
372 L Firmware ≤ 02.00 - DMS 2.1 EN - 03/2011
Motor magnetising inductance (C00092) 246
Motor overload threshold (I²xt) (C00120) 250
Motor parameter identification 59
Motor parameter identification is active 44
Motor selection 54
Motor stator leakage inductance (C00085) 245
Motor stator resistance (C00084) 245
Motor temperature monitoring (PTC) 125
Motor voltage (C00052) 242
N
Nact filter time constant (C00497) 272
Network MCI/AN output words (C00877) 289
Network MCI/CAN input words (C00876) 289
Number of encoder increments (C00420) 266
O
OC1
Power section - short circuit (error message)
212
OC12
I2xt overload - brake resistor (error message)
213
OC2
Power section - earth fault (error message)
212
OC5
Ixt overload (error message)
211
OC6
I2xt overload - motor (error message)
213
OC9
Ixt overload - shutdown limit (error message)
211
OH
Heatsink overtemperature (error message)
210
OH3
Motor temperature (X106) triggered (error
message)
210
OS1
Maximum speed limit reached (error message)
212
Oscillation damping 106
Oscillation damping influence (C00234) 264
OT2
Speed controller output limited (error message)
213
OU
DC bus overvoltage (error message)
211
Output frequency (C00058) 243
Output power (C00980) 292
P
Parameter change-over 172
Password (C00094) 246
Password1 (C304) 265
Password2 (C305) 265
Peak current limitation 64
Plant parameters 58
Port block "LP_Network_In" 224
Port block "LP_Network_Out" 225
Power and energy display 120
Power section identification (C00093) 246
Power-on time meter (C00179) 261
Product type code (C00203) 262
PROFIBUS 220
PROFINET 220
PS01
No memory module (error message)
216
PS02
Par. set invalid (error message)
216
PS03
Par. set device invalid (error message)
216
PS04
Par. set device incompatible (error message)
216
PS31
Ident. error (error message)
217
PTC 125
R
Ramp smoothing, main setpoint (C00134) 251
Rated motor current (C00088) 245
Rated motor frequency (C00089) 245
Rated motor power (C00081) 244
Rated motor speed (C00087) 245
Rated motor torque (C00097) 247
Rated motor voltage (C00090) 246
Rated power brake resistor (C00130) 251
Reaktion brake resistor control (C00175) 260
Reduc. brake chopper threshold (C00174) 260
Reset of error message 207
Resp. to communication error with MCI (C01501) 296
Resp. to control word error (C00594) 276
Resp. to DC bus undervoltage (C00600) 276
Resp. to device overload (Ixt) (C00604) 277
Resp. to encoder open circuit (C00586) 275
Resp. to heatsink temp. > cut-off temp. -5°C (C00582)
275
Resp. to lim. speed controller (C00567) 274
Resp. to LP1 motor phase fault (C00597) 276
Resp. to LS_SetError_x (C00581) 275
Resp. to mains phase failure (C00565) 273
Resp. to max. speed reached (C00607) 277
Resp. to motor overload (I²xt) (C00606) 277
Resp. to motor overtemp. PTC (C00585) 275
Resp. to open circuit AINx (C00598) 276
Resp. to overtemp. brake resistance (C00574) 274
Resp. to speed monitoring (C00579) 274
S
Safety instructions 14
Saving parameters automatically 37
SD10
Speed limit - feedback system 12 (error message)
213

Lenze 8400 motec Specifications

General

Input Voltage	3-phase 380V to 480V AC
Control Mode	Vector control
Communication	CANopen, PROFIBUS, Ethernet
Protection Features	Overcurrent, overvoltage, undervoltage, short-circuit, overtemperature
Relative Humidity	≤ 95 %, no condensation
Altitude	Up to 1000m above sea level
Storage Temperature	-20°C to 65°C