MICRO-EPSILON optoCONTROL 2600 - Table of Contents

optoCONTROL 2600
Contents
1. Safety ........................................................................................................................................ 5
1.1 Symbols Used ................................................................................................................................................. 5
1.2 Warnings .......................................................................................................................................................... 5
1.3 Notes on CE Marking ...................................................................................................................................... 5
1.4 Intended Use ................................................................................................................................................... 6
1.5 Proper Environment ......................................................................................................................................... 6
2. Light Source ............................................................................................................................. 7
3. Functional Principle, Technical Data ....................................................................................... 8
3.1 Measurement Principle .................................................................................................................................... 8
3.2 Structure of a Complete Measurement System .............................................................................................. 8
3.3 Controller ......................................................................................................................................................... 9
3.3.1 Front View of the Controller ............................................................................................................ 9
3.3.2 Rear View of the Controller........................................................................................................... 10
3.4 Operating Modes ........................................................................................................................................... 10
3.5 Technical Data ............................................................................................................................................... 11
3.6 Block Diagram ............................................................................................................................................... 12
3.7 Analog Output ................................................................................................................................................ 12
3.8 Input Zero Point / RESET ............................................................................................................................... 12
3.9 Synchronization ............................................................................................................................................. 12
3.10 Error Output ................................................................................................................................................... 13
3.11 Light Source Control and Trigger Input ......................................................................................................... 13
3.12 Edge Detection Threshold for Transparent Measurement Objects .............................................................. 13
4. Delivery ................................................................................................................................... 14
4.1 Unpacking, Included in Delivery.................................................................................................................... 14
4.2 Storage .......................................................................................................................................................... 14
5. Installation and Mounting ...................................................................................................... 15
5.1 Precautions .................................................................................................................................................... 15
5.2 Mounting the Sensor Unit .............................................................................................................................. 15
5.3 Mounting the Controller ................................................................................................................................. 18
5.4 Power Supply ................................................................................................................................................. 19
5.5 Connecting an Analog Terminal Device ........................................................................................................ 19
5.6 Switching Outputs ......................................................................................................................................... 21
5.7 Switching Inputs ............................................................................................................................................ 22
5.8 Synchronal Signal Input ................................................................................................................................ 22
6. Operation ................................................................................................................................ 23
6.1 Initial Operation .............................................................................................................................................. 23
6.2 Menu Structure .............................................................................................................................................. 23
6.3 Operation ....................................................................................................................................................... 24
6.3.1 Key Functions ............................................................................................................................... 24
6.3.2 Display .......................................................................................................................................... 24
6.3.3 Main Menu .................................................................................................................................... 24
6.3.4 Adjustment with the Video Signal ................................................................................................ 25
6.3.5 Options ......................................................................................................................................... 25
6.3.6 Select Measurement Program ..................................................................................................... 26
6.3.7 Edit Measurement Program (User-specific Programs) ................................................................ 28
6.3.7.1 Zero-Setting Function.................................................................................................. 29
6.3.7.2 Mastering ..................................................................................................................... 30
6.3.7.3 Measurement Programs Segment and Multi-Segment .............................................. 30
6.3.7.4 Display Scaling ............................................................................................................ 31
6.3.7.5 Limit Monitoring ........................................................................................................... 32
6.3.7.6 Averaging .................................................................................................................... 32
6.3.7.7 Median Filter ................................................................................................................ 32
6.3.7.8 Measurement Modes .................................................................................................. 33
6.4 Analog Output ................................................................................................................................................ 36
6.4.1 Setup ............................................................................................................................................ 36
6.4.2 Measurement Conversion ............................................................................................................ 36
6.4.3 Error Handling .............................................................................................................................. 37
6.5 Synchronization of optoCONTROLs ............................................................................................................. 37
6.6 Digital Interfaces ............................................................................................................................................ 39
6.6.1 Interface Parameters .................................................................................................................... 39
6.6.2 Serial Measurement Output ......................................................................................................... 39
6.6.3 Control Commands ...................................................................................................................... 41
6.6.3.1 Information Command ................................................................................................ 43
6.6.3.2 Start Command ........................................................................................................... 43
6.6.3.3 Stop Command ........................................................................................................... 44
6.6.3.4 Reset Command ......................................................................................................... 44
6.6.3.5 Change the Measurement Program ........................................................................... 45
6.6.3.6 Change Edges (Segment and Multi-segment Programs) .......................................... 46
6.6.3.7 Read out min/max Values ........................................................................................... 46
6.6.3.8 Read out min/max Values Followed by Reset ............................................................ 47
6.6.3.9 Read Option Data ........................................................................................................ 48
6.6.3.10 Write Option Data ........................................................................................................ 48
6.6.3.11 Save Option Data ........................................................................................................ 50
6.6.3.12 Read Measurement Program Data ............................................................................. 51
6.6.3.13 Write Measurement Program Data ............................................................................. 52