Modecom MC-4220 - Adding the Secondary LAN IP Address and Subnet Mask

156 pages

Save Page as PDF

To Next Page

To Previous Page

802.11n WLAN ADSL2+ Router

The System is Restarting ...

Adding the Secondary LAN IP address and subnet mask

From the left-hand • LAN menu, click on LAN.

Check on • SecondaryIP.

Type the Secondary IP Address and Subnet Mask.•

Click • Apply Changes.

10.0.0.2

10.0.0.4

Change setting successfully! Click • OK button.

Main Page

Default Chapter2
- Table of Contents2
- Device Requirements5
Introduction5
- Using this Document6
- Special Messages6
Getting to Know the Device6
- Parts Check6
- Front Panel7
- Rear Panel8
Connecting Your Device9
- Configuring Ethernet Pcs10
- Connecting the Hardware10
Easy Setup11
- WAN Configuration11
Getting Started with the Web Pages16
- Accessing the Web Pages16
- Testing Your Setup18
- Internet Access Settings18
- Default Device Settings18
Overview19
- Internet Access Settings20
- About Wireless ADSL2+ Router21
Wireless Network21
- Basic Settings21
- Advanced Settings23
- Security25
- Access Control30
- Allow Listed31
- Wps33
- Operations of AP - AP Being an Enrollee36
- Operations of AP - AP Being a Registrar43
Internet Access48
- Types of Internet Access49
- Configuring Your Pppoe DSL Connection49
- Configuring Your Pppoa DSL Connection51
- Configuring Your Bridged DSL Connection52
- Configuring Your 1483 MER by DHCP53
- Configuring Your 1483 MER by Fixed IP54
- ATM Settings55
- ADSL Settings56
Local Network Configuration58
- Changing the LAN IP Address and Subnet Mask58
- Adding the Secondary LAN IP Address and Subnet Mask61
DHCP Settings62
- DHCP Server Configuration63
- DHCP Relay Configuration65
- DHCP None Configuration67
DNS Configuration69
- DHCP Server Configuration - Attain DNS Automatically69
- DHCP Server Configuration - Set DNS Manually71
- Overview of Dynamic DNS72
- Dynamic DNS Configuration - Dyndns.org74
Ip/Port Filtering77
MAC Filtering79
- Configuring MAC Filtering to Deny for Outgoing Access79
Port Forwarding81
- Configuring Port Forwarding81
- Configuring Custom Applications82
URL Blocking89
- Configuring URL Blocking of FQDN89
- Configuring URL Blocking of Keyword91
Domain Blocking93
- Configuring Domain Blocking93
Dmz95
- Configuring DMZ95
Upnp97
- Configuring Upnp97
- Upnp Control Point Software on Windows ME99
- Upnp Control Point Software on Windows XP with Firewall99
Rip101
ARP Table103
Bridging103
Routing104
Snmp106
Port Mapping107
IP Qos109
Remote Access110
Others111
Diagnostic111
- ATM Loopback113
- Adsl114
- Diagnostic Test115
Commit/Reboot116
Backup/Restore117
- Backup Settings117
- Restore Settings118
- Resetting to Defaults118
- Software Reset119
Password120
- Setting Your Username and Password120
Firmware Update122
- About Firmware Versions122
- Manually Updating Firmware122
ACL Configuration125
- ACL Config125
Time Zone127
- SNTP Server and SNTP Client Configuration Settings127
TR-069 Config132
- TR-069 Configuration132
Statistics133
- Interfaces133
- Adsl134
Configuring Your Computers135
- Configuring Ethernet Pcs135
- Assigning Static Internet Information to Your Pcs138
IP Addresses, Network Masks, and Subnets139
- IP Addresses139
- Subnet Masks141
Troubleshooting141
- Troubleshooting Suggestions142
- Diagnosing Problem Using IP Utilities143
Glossary145

Modecom MC-4220 - Adding the Secondary LAN IP Address and Subnet Mask

Table of Contents