Motion Control Engineering Nidec Element Series

199 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Installation

1-70 Manual # 42-02-2P26

Table of Contents

Safety and Other Symbol Meanings4
Safety Precautions4
Environmental Considerations5
In this Manual6
- Table of Contents7
Installation14
Element Controls14
Safety16
- Personal Safety16
- Equipment Safety16
Specifications17
- Operating Mode Definitions19
User Interface23
- Home Screen23
- Menu Overview25
Component Identification29
- Installation30
Installation32
- Installation Checklist32
- Enclosure Installation32
- Grounding32
- Check for Shorts to Ground33
- AC Power, Motor, Brake33
  - Wire Separation33
- Initial Power Check33
Machine Room Construction Run34
- Construction Run: Cartop34
- Required Drive Settings35
- Required Controller Settings37
  - Brake Pick and Hold Voltages (SCE-BRK Board R3 and Up)37
    - Brake Faults37
    - Brake Transformer Information38
- Initial Speed Calibration38
  - Magnetek38
  - Torqmax38
LS-EDGE Landing System39
- Landing System39
Tape Installation40
- Top and Bottom Hangers40
- Sensor Installation43
  - Sensor Alignment43
- Door Zone Magnets44
- Top Terminal, Bottom Terminal and ETS Magnets45
- Electrical Connection46
- Parameter Settings47
- Hoistway Learn47
  - Offset47
- LS-EDGE Indicators47
LS-RAIL Landing System48
- Mounting Pedestal49
- Electrical Connections50
- Diagnostic Leds50
- Hoistway Limits and Slowdowns50
- Virtual Switches50
- Door Zone Magnets51
  - To Mount the Door Zone Magnets51
- Terminal Magnets52
  - Top and Bottom Terminal52
  - Parameter Settings53
- Hoistway Learn53
  - Offset53
  - Landing System Troubleshooting Tools53
- Door Zone Verification53
- Indicators54
- Permanently Attach Magnets54
Serial Hall and Car Call Boards55
- Hall Calls55
  - General Installation55
- Serial Car Call Board58
  - Installation Instructions58
- Lanterns and Pis61
  - Serial PI Configuration61
Door Operator62
- Door Position Monitor Switch62
Load Weigher62
Traction Elevator Adjustment63
- Counterweight Position63
- Brake Coordination63
- Hoistway Learn (Landing System Learn)64
- Tuning64
  - Magnetek HPV 900 Series 264
  - Torqmax F564
- Drive Response65
  - Tuning66
- S-Curve66
- One Floor Run67
- Contract Speed Operation67
  - Magnetek67
  - Torqmax67
- Relevel Operation67
Terminal Switch Configuration68
- Terminal Switch Learn69
  - NTS/ETS Switches with Full Stroke Buffers69
  - NTS/ETSL Switches with Reduced Stroke Buffers70
    - Virtual NTS/ETSL (Landing System Position Count)70
    - Physical ETSL (Cam-Operated Switches)70
- Adjustment Problems71
Duplex Operation73
- Interconnect73
  - Power Phasing73
Traction Acceptance Tests74
- Manual Tests74
- Automated Tests76
Passcode (Restricted Mode)81
Backup the Parameter Settings81
- Passcode81
In this Section83
Using the Touch Screen/Obd84
- Home84
- Using the Touch Screen85
- Shortcuts86
- Menu Tree86
Screen Descriptions87
- Spare Inputs101
- Spare Outputs103
- Acronyms104
Web Browser Access111
- Web Setup111
- Access111
USB Parameter Transfer111
Event Log Archive/Email112
- Event Log Archive/E-Mail112
- USB Archive112
- Ethernet Archive112
- Email112
Troubleshooting Reference113
- Bus Voltage Testpoints and Fuse Locations113
- Touch Screen Tools114
- Circuit Board Descriptions116

Related product manuals