Motion Control Engineering Nidec Element Series

To Next Page

To Previous Page

Configuration and Troubleshooting

2-40 Manual # 42-02-2P26

SCE-CPU

The SCE-CPU board provides system logic and control. The touchscreen is mounted on this

board as are machine room control switches.

Main Page

Safety and Other Symbol Meanings4
Safety Precautions4
Environmental Considerations5
In this Manual6
- Table of Contents7
Installation14
Element Controls14
Safety16
- Personal Safety16
- Equipment Safety16
Specifications17
- Operating Mode Definitions19
User Interface23
- Home Screen23
- Menu Overview25
Component Identification29
- Installation30
Installation32
- Installation Checklist32
- Enclosure Installation32
- Grounding32
- Check for Shorts to Ground33
- AC Power, Motor, Brake33
  - Wire Separation33
- Initial Power Check33
Machine Room Construction Run34
- Construction Run: Cartop34
- Required Drive Settings35
- Required Controller Settings37
  - Brake Pick and Hold Voltages (SCE-BRK Board R3 and Up)37
    - Brake Faults37
    - Brake Transformer Information38
- Initial Speed Calibration38
  - Magnetek38
  - Torqmax38
LS-EDGE Landing System39
- Landing System39
Tape Installation40
- Top and Bottom Hangers40
- Sensor Installation43
  - Sensor Alignment43
- Door Zone Magnets44
- Top Terminal, Bottom Terminal and ETS Magnets45
- Electrical Connection46
- Parameter Settings47
- Hoistway Learn47
  - Offset47
- LS-EDGE Indicators47
LS-RAIL Landing System48
- Mounting Pedestal49
- Electrical Connections50
- Diagnostic Leds50
- Hoistway Limits and Slowdowns50
- Virtual Switches50
- Door Zone Magnets51
  - To Mount the Door Zone Magnets51
- Terminal Magnets52
  - Top and Bottom Terminal52
  - Parameter Settings53
- Hoistway Learn53
  - Offset53
  - Landing System Troubleshooting Tools53
- Door Zone Verification53
- Indicators54
- Permanently Attach Magnets54
Serial Hall and Car Call Boards55
- Hall Calls55
  - General Installation55
- Serial Car Call Board58
  - Installation Instructions58
- Lanterns and Pis61
  - Serial PI Configuration61
Door Operator62
- Door Position Monitor Switch62
Load Weigher62
Traction Elevator Adjustment63
- Counterweight Position63
- Brake Coordination63
- Hoistway Learn (Landing System Learn)64
- Tuning64
  - Magnetek HPV 900 Series 264
  - Torqmax F564
- Drive Response65
  - Tuning66
- S-Curve66
- One Floor Run67
- Contract Speed Operation67
  - Magnetek67
  - Torqmax67
- Relevel Operation67
Terminal Switch Configuration68
- Terminal Switch Learn69
  - NTS/ETS Switches with Full Stroke Buffers69
  - NTS/ETSL Switches with Reduced Stroke Buffers70
    - Virtual NTS/ETSL (Landing System Position Count)70
    - Physical ETSL (Cam-Operated Switches)70
- Adjustment Problems71
Duplex Operation73
- Interconnect73
  - Power Phasing73
Traction Acceptance Tests74
- Manual Tests74
- Automated Tests76
Passcode (Restricted Mode)81
Backup the Parameter Settings81
- Passcode81
In this Section83
Using the Touch Screen/Obd84
- Home84
- Using the Touch Screen85
- Shortcuts86
- Menu Tree86
Screen Descriptions87
- Spare Inputs101
- Spare Outputs103
- Acronyms104
Web Browser Access111
- Web Setup111
- Access111
USB Parameter Transfer111
Event Log Archive/Email112
- Event Log Archive/E-Mail112
- USB Archive112
- Ethernet Archive112
- Email112
Troubleshooting Reference113
- Bus Voltage Testpoints and Fuse Locations113
- Touch Screen Tools114
- Circuit Board Descriptions116

Motion Control Engineering Nidec Element Series

Table of Contents

Related product manuals