Munters Trio Poultry Controller

To Next Page

To Previous Page

2. Enable Fan Cycle and Fan Rotation (Fan Rotation does not appear unless Fan Cycle

is enabled.)

3. Go to Climate > Ventilation.

4. After enabling fans, click on any fan that you want to rotate. appears.

5. Click the icon. Repeat for any required fans.

Main Page

Table of Contents3
Introduction7
Disclaimer7
Notes7
Using the Trio Touch Screen8
Icons8
Dashboard9
Basic Setup11
Defining the General Settings11
Defining the Preferences11
Defining the Time/Date12
Defining the House Setting13
Flock Settings13
Defining the Flock Settings Parameters13
Manual Set up14
New Flock Wizard15
Defining House Modes18
Adjusting the Bird Count19
Temperature Settings21
What Is the Temperature Curve21
Configuring the Temperature Curve22
Defining the Temperature Curve Parameters22
Defining Temperature Curve Settings23
Emergency Temperature Control23
Temperature Humidity Index24
Introduction to Ventilation26
Defining the Minimum and Maximum Ventilation26
Defining the Fans/Ventilation Scheme27
Basic Ventilation27
Extra Ventilation28
Tunnel Ventilation29
Minimum and Maximum Ventilation30
Building Structure Summary30
Defining Basic Ventilation31
Defining Dynamic Ventilation32
Ventilation by Weight34
How Does Ventilation by Weight Work34
Defining the Ventilation by Weight Parameters34
Adding a Curve35
Levels of Ventilation36
Configuring the Basic Ventilation Settings36
Basic Ventilation37
Defining Basic Ventilation37
Fan Options39
Minimum Ventilation Cycle40
Analog Fans42
Fans (Efficiency Fan)43
Fan Rotation44
Inlet and Curtain Ventilation46
Level Control47
Static Pressure Control48
Static Pressure in Minimum Ventilation or Extra Ventilation48
Static Pressure Main Screen49
Static Pressure Settings Screen49
High Static Pressure Alarm State50
Extra Ventilation50
Introduction to Extra Ventilation50
Defining Extra Ventilation50
Tunnel Ventilation52
Defining the Tunnel Ventilation Parameters53
Defining the Tunnel Ventilation Settings56
Tunnel Doors56
Defining the Wind Chill Factor57
Calibrating the Inlet/Tunnel Door58
Stir Fan59
Cooling Functions60
Cooling Principles60
Selecting the Cooling Mode61
Continuous Cooling62
Cycle Cooling63
Ramping Cooling64
Heating Functions65
Central Heaters65
Analogue Heaters66
Heat Cycles67
Zone Heaters68
Brood Area70
Feed and Silo Management73
Feeding Summary73
Setting up Feeding73
Configuring the Silo75
Batch Weighing System77
External Batch bin Installation77
Electronic Batch Weighing Installation79
Wiring and Mapping79
Batch bin Calibration83
Configuration85
Dashboard86
Pausing Batching Mixing and Feed Mixing87
Batch Weigher Alarms88
Lighting Program90
On/Off Lights90
Volt Variable Lights92
Light Settings95
Expected Bird Weight96
Reference Bird Curve96
Curve Enabled96
Curve Disabled98
Male/Female Weighing100
Gender Separated Weighing100
Non-Separated Weighing101
Air Quality102
Defining the Air Quality Parameters102
Defining the Air Quality Settings103
Timers105
Alarms107
Defining the Alarm Parameters107
Alarm Definitions107
Alarm Test108
Manual Test108
Scheduled Tests108
Viewing the Alarms109
Defining the Auxiliary Alarms109
Sending a General Alarm111
Water Alarm111
History113
Climate and Air Quality113
Alarms and Events114
Water and Feed History115
Devices History116
Bird Weight History117
Resetting, Saving and Loading Settings, Updating Software118
Resetting the Settings118
Resetting the Trio CPU and Sensor Connections119
Saving or Loading the Settings120
Viewing the Log120
Updating the Software121
Warranty122

Munters Trio Poultry Controller - Page 45

Table of Contents

Other manuals for Munters Trio Poultry Controller

Related product manuals