Pentair EASYTOUCH PL4 - Page 43

EASYTOUCH
®
PL4/PSL4 Control Systems User’s Guide
  35
IntelliFlo VS and VSF+SVRS Settings
Selecting the IntelliFlo PUMP TYPE
ToaccesstheIntelliFlomenu:
MENUsSETTINGSsINTELLIFLOwPUMP#1
Up/Down button: ChoosePump #1.
Right button: SelectPump #1.
Right button: SelectPump Type.Note:TochangethecurrentpumptypeforPump
#1.presstheUp/DownbuttonandselectY,thenpresstheRight button.Tocontinue
tothePump#1settingsmenu,presstheRight button (orMenutoexit).
Settings Menu: IntelliFlo
®
Pump (Continued)
Connecting Power to the IntelliFlo Pump
TheIntelliFlopumpisdesignedtobepermanentlyconnectedtoitspowersource.Typicallythepumpreceives
powerdirectlyfromthecircuitbreaker.Nocontactorormotorstarterisrequired.Thedrivecontrolsthe
startingandstoppingofthepump.IftheIntelliFlopumpisconnectedtoanautomationsystem,suchasthe
EasyTouchPL4/PSL4ControlSystem,thedrivemustbepowereduptoreceiveandrespondtotheRS-485
serialcommunicationfromtheautomationsystem.However,thepumpcanbeoperatedin“stand-alone”
mode,startingandstoppingwhenpowerisappliedorremoved.Whenthedrivepowersupitwillreturnto
themodeandrunstatusthatitwasinwhenpowerwasremoved.Thissetupisappropriateifyouneedtouse
existingrelaysortimers.
Assigning an IntelliFlo VS 3050 pump address
BeforeassigningapumpaddressattheEasyTouchPL4/PSL4Control
Systemindoor,wirelessoroutdoorcontrolpanel,rstsettheaddresson
the pump itself.Thepump'sdefaultaddressispump#1.
ToassignanIntelliFloVS3050pumpaddress:
1. BesurethatthepumpispoweredonandthegreenpowerLED
ison.
2. PresstheStop buttonstostopthepump.
3. PressandholdboththeStart and Stop buttonsuntilthered
LEDwillstartsashing,thenpressoneofthefourspeed
buttons(1-4)toselectwhichaddresstoassignthepump.For
example,ifyouareassigningthepumpaspump#1,thenpress
Speedbuttonnumber1.
4. PressandholdboththeStart and Stop buttonstosavethe
address.Repeattheprocessfortheotherpumps.
NOTE: INTELLIFLO IN “SERVICE MODE” - IntelliFlo pumps will STOP when the system is in ‘Service” mode.
NOTE: INTELLIFLO “FREEZE” PROTECTION - If the IntelliFlo pump is on due to a freeze condition (not switch
on from a relay circuit), and if a freeze protect for a certain speed is set, this setting takes priority even if the
previous setting is lower than the default circuit speed. If no “freeze” protection is set, the pump will be forced on
at the default circuit speed. Any programmed or manual operation that actually switches on a circuit, will cause the
pump to run at that speed if it is higher.
SELECT PUMP TYPE: Up/Down buttons: ChooseVSorVSF+SVRS.
Menu button: PresstheMENUbuttontosaveselectionandreturntotheselected
pump’smenusettings(seeVSandVSFpumpsettingsdescriptionsbelow)
Pump #1



Changing Pump1’s
Type will config
it to default.
Continue ? N
Pump Type
Speeds
Priming
Status



IntelliFloVSPumpSpeedbuttons(1-4)
Speed
1
Speed
2
Speed
3
Speed
4