Primes PROFINET - Status LED

98 pages

Save Page as PDF

To Next Page

To Previous Page

PowerMeasuringModule PMM

35,0(6

Revision 13 EN - 02/2023

7.4.5 Status LED

LED Color Mode Meaning

Power Green On Supply voltage is connected.

Tab. 7.15: Status LED

Main Page

Table of Contents4
Basic Safety Notes8
Symbols and Conventions10
About this Operating Manual11
Device Description12
Type Overview12
Distinction by Interface and Absorber Type12
Distinction by the Interface, the Possibility to Measure Pulsed Lasers and a Reduced Thermalization Time13
Distinction by the Interface and the Measurable Wavelength Range13
Devices with UL Marking13
Functional Description14
Measuring Principle14
Explanation of the Product Safety Labels15
Warning of Hand Injuries/Damage to the Device15
Warning of Internally Connected Power Ports15
Scope of Delivery and Optional Accessories16
Transport and Storage16
Mounting17
Conditions at the Installation Site17
Installation in the Laser System17
Prepare Mounting17
Possible Mounting Positions17
Align the Device18
Mount the Device18
Removal from the Laser System20
Connections21
Interface Overview21
PROFINET ® /PROFINET ® LWL (Fiber Optics)22
Connectors22
Pin Assignment Data Connector XF1/XF223
Pin Assignment Power Supply XD1/XD223
Status Leds23
Profibus24
Connectors24
Pin Assignment Data Connector XF1 In/Xf2 out24
Pin Assignment Power Supply XD1/XD225
Status Leds25
Parallel26
Connectors26
Pin Assignment Power Supply XD127
Pin Assignment Input, 4-Channel XG1 in27
Pin Assignment Output, 16-Channel XG2 out28
Status LED29
Devicenet30
Connectors30
Pin Assignment Connectors XZ1 In/Xz2 out30
Status Leds31
Ethernet/Ip32
Connectors32
Pin Assignment Data Connector XF1/XF232
Pin Assignment Power Supply XD1/XD233
Status Leds33
Ethercat34
Connectors34
Pin Assignment Data Connector XF1/XF234
Pin Assignment Power Supply XD1/XD235
Status Leds35
Laser Parameter Setting37
Setting the Laser Rise Time37
Maximum Power Density38
Minimum and Maximum Energy Input Per Measurement39
Number of Measuring Cycles (Repetitive Measurements)40
Waiting Times until the Next Measurement in Repepetive Measurements41
Calculation of the Irradiation Time41
Measurement with Pulsed Lasers (Only PMM Type Ap3S)42
Measuring44
Warning Messages44
General Flow Diagram of a PMM Measurement45
PLC Control Program Sequence of the PMM47
Internal Conditions47
Shutter Conditions48
Measurement Cycle Details49
Preparing the Measurement49
Opening the Shutter49
Determination of the Irradiation Time49
Execution of the Power Measurement50
Evaluate Measurement51
Time-Optimized Measuring Procedure51
Measuring Procedure Parallel-Interface52
Programming Model53
Registry Settings53
Configuration Data54
Variables55
Status Information55
Commands56
PROFINET ® or PROFIBUS ® Connection57
GSDML File (PROFINET )57
GSD File (PROFIBUS )58
Devicenet™ or Ethernet/Ip™ Connection60
Hardware/Software60
Hardware60
Software60
Data Model61
PMM with Devicenet61
Setting the Devicenet™ Address and the Baud Rate63
Integrating Devicenet™ Scanner into Devicenet63
Importing EDS File64
Bus Configuration with Rsnetworx65
Debugging68
PMM with Ethernet/Ip71
Module Configuration71
Setting the IP Address71
Setting the IP Address Via a Web Browser72
Module Definition74
Ethercat ® Connection77
Connect the PMM to the Device Tree77
Process Data Mapping78
Maintenance and Service82
Maintenance Intervals82
Cleaning82
Cleaning the Device Surfaces82
Cleaning the Protective Window82
Exchanging the Protective Window82
Warning Messages83
Exchanging the Protective Window of the PMM84
Exchangeable Cassette85
Replacing the Exchangeable Cassette85
Replacing the Protective Window of the Exchangeable Cassette86
Measures for the Product Disposal87
Technical Data88
Dimensions91
Declaration of Incorporation of Partly Completed Machinery92
Manufacturer's Declaration94
Appendix95
Max. Laser Power Depending on the Irradiation Time for Devices with Standard Absorber95
Max. Laser Power Depending on the Beam Diameter for Devices with Standard Absorber95
Max. Laser Power Depending on the Irradiation Time for Devices with Advanced Absorber96
Max. Laser Power Depending on the Beam Diameter for Devices with Advanced Absorber96
Add-On Instruction of the Rslogix 5000 Control Software97

Primes PROFINET - Status LED

Table of Contents

Related product manuals