IV Contents ECODRIVE03-SGP-03VRS
DOK-ECODR3-SGP-03VRS**-WA01-EN-P
5 Description of Diagnostic Messages B…; C…, D… and A 5-1
5.1 Command Diagnostic Messages B…, C… and D…...................................................................... 5-1
B100 Command Release motor holding brake........................................................................ 5-2
B101 Command not enabled ................................................................................................... 5-2
B200 Brake check command................................................................................................... 5-2
B201 Brake check only with drive enable ................................................................................ 5-2
B202 Error during abrasion of the brake.................................................................................. 5-2
B203 Brake torque too low.......................................................................................................5-3
C100 Communication phase 3 transition check ...................................................................... 5-3
C101 Invalid communication parameter (S-0-0021)................................................................ 5-3
C102 Limit error communication parameter (S-0-0021) .......................................................... 5-3
C104 Config. IDN for MDT not configurable ............................................................................ 5-4
C105 Configurated length > max. length for MDT................................................................... 5-4
C106 Config. IDN for AT not configurable ............................................................................... 5-4
C107 Configurated length > max. length for AT ...................................................................... 5-5
C108 Time slot parameter > Sercos cycle time....................................................................... 5-5
C109 Position of data record in MDT (S-0-0009) even ...........................................................5-5
C110 Length of MDT (S-0-0010) odd ...................................................................................... 5-6
C111 ID9 + Record length - 1 > length MDT (S-0-0010)......................................................... 5-6
C112 TNcyc (S-0-0001) or TScyc (S-0-0002) error................................................................. 5-6
C113 Relation TNcyc (S-0-0001) to TScyc (S-0-0002) error................................................... 5-7
C114 T4 > TScyc (S-0-0002) - T4min (S-0-0005) ................................................................... 5-7
C115 T2 too small....................................................................................................................5-7
C118 Order of MDT configuration wrong................................................................................. 5-7
C200 Communication phase 4 transition check ...................................................................... 5-8
C201 Invalid parameter(s) (->S-0-0022).................................................................................. 5-8
C202 Parameter limit error (->S-0-0022)................................................................................. 5-8
C203 Parameter calculation error (->S-0-0022) ...................................................................... 5-9
C204 Motor type P-0-4014 incorrect........................................................................................ 5-9
C210 Feedback 2 required (->S-0-0022)................................................................................. 5-9
C211 Invalid feedback data (->S-0-0022).............................................................................. 5-10
C212 Invalid amplifier data (->S-0-0022)............................................................................... 5-10
C213 Position data scaling error............................................................................................ 5-10
C214 Velocity data scaling error............................................................................................ 5-11
C215 Acceleration data scaling error..................................................................................... 5-11
C216 Torque/force data scaling error .................................................................................... 5-12
C217 Feedback1 data reading error...................................................................................... 5-12
C218 Feedback 2 data reading error..................................................................................... 5-13
C220 Feedback 1 initializing error ......................................................................................... 5-13
C221 Feedback 2 initializing error ......................................................................................... 5-14
C223 Input value for max. range too high.............................................................................. 5-14
C227 Modulo range error....................................................................................................... 5-14
C228 Controller type S-0-0140 wrong ................................................................................... 5-15
C234 Encoder combination not possible ............................................................................... 5-15
C235 Load-side motor encoder with inductance motor only ................................................. 5-15
To Next Page
Loading...
Need help?
General
