Rockwell Automation Allen-Bradley POINT Guard - Configure the Smartguard Controller; Set up the Input and Output Connections

212 pages

To Next Page

To Previous Page

Rockwell Automation Publication 1734-UM013J-EN-P - July 2014 119

Configure the Module for a SmartGuard Controller Chapter 6

Configure the SmartGuard

Controller

Follow the procedures in the next sections to configure input and output

connections to the controller and complete the controller’s setup.

Set Up the Input and Output Connections

1. In RSNetWorx for DeviceNet software, right-click the SmartGuard

controller and choose Properties.

2. Click the Safety Connection tab to see a list of all Safety I/O modules

currently in your project.

Main Page

Default Chapter5
- Table of Contents5
Preface11
- Studio 5000 Environment11
- Access Product Release Notes12
- Terminology12
- Additional Resources13
Chapter 115
POINT Guard I/O Overview15
- Understand Suitability for Use15
- POINT Guard I/O Modules in CIP Safety Systems17
- Safety Precautions17
  - Installing and Replacing Modules17
- Safety Application Requirements21
Chapter 2 Safe States23
- POINT Guard Digital I/O Modules23
- POINT Guard I/O Analog Input Module24
Safety Inputs, Safety Outputs, and Safety Data23
- Safety Inputs (1734-IB8S)24
- Safety Analog Inputs (1734-IE4S)31
- Safety Outputs (1734-OB8S)39
- Muting Lamp Operation (1734-IB8S)40
- I/O Status Data42
  - Digital I/O Status Data42
  - Analog I/O Status Data43
- Choosing a Power Supply45
- And Modules in a System Power Supply Examples46
Chapter 3 Power Supply Examples46
- Example 1: Isolating Field Power Segments47
  - Example 2: POINT Guard I/O Used with AC I/O Modules47
- Placing Series a Digital and Analog Modules48
- Placing Series B Digital Modules48
Chapter 4 Install the Module Precautions52
- North American Hazardous Location Approval53
- Environment and Enclosure53
- Preventing Electrostatic Discharge54
- Precautions52
  - European Hazardous Location Approval52
- Mount the Module54
- Wire Modules58
  - Terminal Layout59
- Connection Details60
- Wiring Examples62
- Setting up the Module73
- Add and Configure the Ethernet Bridge Module74
Chapter 574
- Add and Configure the 1734 Ethernet Adapter75
- Add and Configure Safety Digital Input Modules77
- Add and Configure Safety Digital Output Modules86
  - Add the Safety Digital Output Module86
  - Configure the Safety Digital Outputs90
- Add and Configure Safety Analog Input Modules91
- Values and States of Tags100
- Configure Safety Connections102
- Configuration Ownership103
- Modules104
- Saving and Downloading the Module Configuration104
- Using Controlflash Software to Update POINT Guard I/O104
- Before You Begin105
Chapter 6106
- Set the Node Address106
- Smartguard Controller Set the Node Address106
- Auto-Addressing with a 1734-PDN Adapter108
- Set up Your Devicenet Network109
- Configure the POINT Guard I/O Modules110
- Configure the Smartguard Controller119
  - Set up the Input and Output Connections119
  - Complete the Set up of the Smartguard Controller123
- Save and Download Module Configuration124
- Configure the Module in Rsnetworx for Devicenet Software125
- Add the POINT Guard I/O Module to the Controller Project126
Chapter 7126
- Complete the Safety Configuration129
- Download the Devicenet Network Configuration131
- Verify Your Devicenet Safety Configuration131
- The Safety Network Number137
Chapter 8138
- Manually Setting the Safety Network Number138
- Resetting a Module to Out-Of-Box Condition139
  - By Using the Logix Designer Application139
  - By Using Rsnetworx for Devicenet Software140
- Network141
- Replacing a Module in a Guardlogix System on an Ethernet/Ip141
- Controller on a Devicenet Network147
- Replacing a Module When Using a Smartguard or Guardlogix147
Appendix A152
- Configuration Lock152
- Module152
- Network Status152
- 1734-IB8S Safety Input Status153
- 1734-IE4S Safety Analog Input Status153
- 1734-IE4S Sensor Power153
- Power153
- 1734-OB8S Safety Output Status154
- Message Instructions155
Appendix B156
- Configure the Message Instruction156
- Class, Instance, and Attribute Data for I/O Modules157
Appendix C Technical Specifications for Series a Modules161
- Safety Digital Input Module Specifications161
- Safety Digital Output Module Specifications163
- Safety Analog Input Module Specifications164
- Technical Specifications for Series B Modules173
  - Safety Digital Input Module Specifications173
  - Safety Digital Output Module Specifications176
- Environmental Specifications177
- Certifications179
- Legislations and Standards179
Appendix D182
- Series a Safety Data182
- Series B Safety Data184
Appendix E188
Appendix E189
Appendix E190
Appendix F191
- Input Assemblies191
- Analog Input Assemblies192
- Output Assemblies192
- Configuration Assemblies194
- Using Data from Modules Configured Via the Generic Profile200
- 1734-UM013F-EN-P, June 2012201
- 1734-UM013G-EN-P, August 2012201
- 1734-UM013H-EN-P, August 2012201
- 1734-UM013I-EN-P, May 2013201
Appendix G201
- Rockwell Automation Publication 1734-UM013J-EN-P - July201
- 1734-UM013C-EN-P, August 2010202
- 1734-UM013D-EN-P, September 2011202
- 1734-UM013E-EN-P, March 2012202
- 1734-UM013A-EN-P, February 2009203
- 1734-UM013B-EN-P, June 2009203

Rockwell Automation Allen-Bradley POINT Guard - Configure the Smartguard Controller; Set up the Input and Output Connections

Table of Contents

Related product manuals