Roland INTEGRA-7 User Manual (English)

Other manuals for Roland INTEGRA-7

Owners & Installation Manual68 pages

Owner's Manual68 pages

Questions and Answers:

B
Brian HaneyAug 18, 2025
Why is there no sound coming from my Roland Recording Equipment?
- J
  Jeanette SimonAug 18, 2025
  If you are experiencing no sound with your Roland Recording Equipment, ensure that the connected amplifier or speaker is powered on. Also, verify that the volume on any connected devices is appropriately adjusted, and that the [VOLUME] knob on your Roland device is not set to the minimum level. Check that your amp, speakers, or headphones are correctly connected. If using headphones produces sound, inspect your connection cables and equipment for any malfunctions. Confirm that the MIDI transmit channel of any connected device matches the MIDI receive channel (Rx Channel) of the Roland unit, and use a connection cable that does not contain a resistor.
R
ramirezheatherAug 21, 2025
What to do if the sound from Roland Recording Equipment is distorted?
- B
  Brian RayAug 21, 2025
  If your Roland Recording Equipment is producing a distorted sound, try lowering the [VOLUME] knob. Also, check the “Output Gain” setting in the “SOUND” system settings to ensure it is not excessively high. If you are using an input signal (front or rear), make sure the input level is not clipping, indicated by the PEAK indicator on the front panel lighting up. Adjust the volume of the connected device to prevent the PEAK indicator from lighting.
T
tmendozaAug 23, 2025
Why won't my Roland Recording Equipment turn on?
- D
  Diana CooperAug 23, 2025
  If your Roland Recording Equipment is not turning on, ensure that the AC power cord is correctly connected. It is crucial to only use the AC power cord included with the unit to avoid any risk of malfunction.
A
audrey29Aug 26, 2025
Why are notes broken off on my Roland Recording Equipment?
- C
  carolwintersAug 26, 2025
  If notes are being cut off when using your Roland Recording Equipment, it might be due to exceeding the maximum number of simultaneous notes (128). Try reducing the number of layers in the Live Set you're using or increase the voice reserve setting for layers where notes must not drop out.
M
Melissa SheltonAug 27, 2025
Why is there no sound from a specific part on my Roland Recording Equipment?
- K
  Kenneth RiveraAug 27, 2025
  If you can't hear sound from a specific part on your Roland Recording Equipment, check if the volume level of that part has been lowered and adjust the Level to raise it. Also, verify that the part is not muted by changing the mute setting to “-.” Finally, ensure that the Rx Switch of the part is turned on.
J
Jeffrey MossAug 30, 2025
Why is the pitch wrong on my Roland Recording Equipment?
- X
  Xavier GutierrezAug 30, 2025
  If the pitch of your Roland Recording Equipment sounds wrong, start by checking the “Master Tune” setting in the “SOUND” system settings. Then, verify the pitch bend messages transmitted by any external MIDI devices connected to your equipment. Finally, check the Coarse Tune and Fine Tune settings to ensure they are properly configured.
E
eric62Sep 1, 2025
How to stop my Roland Recording Equipment from turning off unexpectedly?
- T
  Tracy BowersSep 1, 2025
  If your Roland Recording Equipment unexpectedly turns off, you can prevent this by changing the “Auto Off” system setting to “OFF.” This will ensure the unit stays on as long as it's powered.
M
Mallory PaulSep 3, 2025
Why can’t I back up to a USB flash drive on my Roland Recording Equipment?
- M
  martinezcharlesSep 3, 2025
  If you are unable to back up data to a USB flash drive using your Roland Recording Equipment, ensure that the USB flash drive has sufficient free space. If space is not the issue, format the USB flash drive on the Roland unit.
D
Darryl BurnsSep 6, 2025
What to do if Roland Recording Equipment doesn't recognize USB flash drive?
- C
  Casey KramerSep 6, 2025
  If your Roland Recording Equipment is not recognizing a USB flash drive, ensure that the drive is formatted as FAT. The Roland unit can only recognize USB flash drives formatted as FAT. Drives with other formats like NTFS will not be recognized. You can format the USB flash drive on the Roland unit.
D
Dawn GeorgeSep 8, 2025
Why can’t I hear the audio signal from the computer on my Roland Recording Equipment?
- J
  Jamie BrownSep 8, 2025
  If you can't hear the audio signal from your computer through your Roland Recording Equipment, the sampling rate of the audio signal from the computer might be different from the sampling rate of the Roland unit itself. Change the Sampling Rate setting of the Roland unit to match the sampling rate of the audio signal from your computer.

Roland INTEGRA-7 Specifications

General

Audio (L/R) in	2
USB connector type	USB Type-A
Audio (L/R) out	5
Digital audio coaxial out	1
Product color	Gray
Sound effects	Chorus, Reverberation
Built-in speaker(s)	No
Chorus effects quantity	3
Reverberation effects quantity	6
MIDI in	Yes
6.35 mm (1⁄4-inch) input	4
6.35 mm (1⁄4-inch) output	8
Display type	LCD
Power source type	AC