Roland INTEGRA-7

95
MFX Parameters
62: Enhancer -> Chorus
Chorus
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
Balance W
Balance W
Balance D
Balance D
Parameter Value Explanation
Enhancer Sens # 0–127 Sensitivity of the enhancer
Enhancer Mix # 0–127
Level of the overtones generated by
the enhancer
Chorus Pre Delay 0.0–100.0 ms
Adjusts the delay time from the
direct sound until the chorus sound
is heard.
Chorus Rate #
0.05–10.00 Hz,
note
Frequency of modulation
Chorus Depth 0–127 Depth of modulation
Chorus Balance #
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is sent
through the chorus (W) and the
sound that is not sent through the
chorus (D).
Level 0–127 Output Level
63: Enhancer -> Flanger
Feedback
Flanger
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
Balance W
Balance W
Balance D
Balance D
Parameter Value Explanation
Enhancer Sens # 0 –127 Sensitivity of the enhancer
Enhancer Mix # 0 –127
Level of the overtones generated by
the enhancer
Flanger Pre
Delay
0.0–100.0 ms
Adjusts the delay time from when
the direct sound begins until the
anger sound is heard.
Flanger Rate #
0.05–10.00 Hz,
note
Frequency of modulation
Flanger Depth 0 –127 Depth of modulation
Flanger
Feedback #
-98–+98 %
Adjusts the proportion of the
anger sound that is fed back into
the eect. Negative “-” settings will
invert the phase.
Flanger Balance
#
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is sent
through the anger (W) and the
sound that is not sent through the
anger (D).
Level 0 –127 Output Level
64: Enhancer -> Delay
Feedback
Delay
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
Balance W
Balance W
Balance D
Balance D
Parameter Value Explanation
Enhancer Sens # 0 –127 Sensitivity of the enhancer
Enhancer Mix # 0 –127
Level of the overtones generated by
the enhancer
Delay Time 0–2600 ms, note
Adjusts the delay time from the
direct sound until the delay sound
is heard.
Delay Feedback
#
-98–+98 %
Adjusts the proportion of the delay
sound that is fed back into the
eect. Negative “-” settings will
invert the phase.
Delay HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the eect will be
cut. If you do not want to cut the
high frequencies, set this parameter
to BYPASS.
Delay Balance #
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is sent
through the delay (W) and the
sound that is not sent through the
delay (D).
Level 0 –127 Output Level
65: Chorus -> Delay
Feedback
Delay
L in
R in
L out
R out
Balance W
Balance W
Balance D
Balance D
Chorus
Balance W
Balance W
Balance D
Balance D
Parameter Value Explanation
Chorus Pre Delay 0.0–100.0 ms
Adjusts the delay time from the
direct sound until the chorus sound
is heard.
Chorus Rate #
0.05–10.00 Hz,
note
Frequency of modulation
Chorus Depth 0–127 Depth of modulation
Chorus Balance #
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the chorus sound (W)
Delay Time 0–2600 ms, note
Adjusts the delay time from the
direct sound until the delay sound
is heard.
Delay Feedback
#
-98–+98 %
Adjusts the proportion of the delay
sound that is fed back into the
eect. Negative “-” settings will
invert the phase.
Delay HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the eect will be
cut. If you do not want to cut the
high frequencies, set this parameter
to BYPASS.
Delay Balance #
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is sent
through the delay (W) and the
sound that is not sent through the
delay (D).
Level 0–127 Output Level